Lightware MX8x8DVI-HDCP-Pro Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 108

background image

Page 80 / 109

All outputs:

this option means that the modified parameters are applied to all

output ports.

Info:

After closing this window, the Current Output option will be selected regardless of
which was active at the time of closing. It is to avoid setting All Outputs by mistake.

Reload factory defaults

Current output:

Reloads the default values to the currently selected output.

All outputs

: Loads the factory default values to all outputs.

Set signal properties for output

Mode

It  specifies  the  desired  type  of  outputted  signal  on  the
port  (Auto,  DVI,  HDMI  24-bit,  HDMI  30-bit  or  HDMI  36-
bit).
If  you  select  Auto,  the  system  will  configure  the  mode
automatically  based  on  the  capabilities  of  your  display
and the incoming signal.

Color space

Convert the color space on the output to the given type.
You are able to force any-to-any color space conversion
or leave this field on Auto. Please note that DVI signals
support only RGB color space.

Color range

Defines color range conversion for the output port.

LPCM subsample

Defines the subsampling of the PCM audio signal. This
setting applies only to the 2-channel PCM audio. The
minimum of the new sampling frequency is 44.1kHz.

HDCP

Determines  HDCP  encryption  for  the  output  signal.  In
automatic mode the encryption depends on the incoming
signal. You are also able to force HDCP on non protected
signals.  Removing  the  encryption  from  a  content
protected  video  is  not  possible  due  to  the  limitations  of
the specification.

Drive current

It specifies the drive current of the internal crosspoint
circuit. It is strongly recommended to leave this value at
the default 12mA.

General

Monitor present

Shows if there is a sink device attached.

Output signal

Actual type and color depth of the transmitted signal over
this port.

Active signal

Shows if there is a valid signal routed to this output port.

HDCP

Shows if the HDCP encryption is currently enabled or
disabled.

HotPlug Detect

Shows if the sink device is ready to receive the signal.

Display

HDMI capable

Shows whether the sink supports HDMI.

HDCP capable

Shows if the HDCP authentication was successful or
failed.

HDCP repeater

Shows if the sink device is an HDCP repeater or not.

«
...
78
79
80
81
82
...
»

Содержание MX8x8DVI-HDCP-Pro













































































































Отзывы:

Нет отзывов

Похожие инструкции для MX8x8DVI-HDCP-Pro

Бренд: NAD Страницы: 36

Бренд: NAD Страницы: 3

Бренд: Fender Страницы: 20

Бренд: Hagerman Technology Страницы: 20

Бренд: Nakamichi Страницы: 23

Бренд: Laney Страницы: 7

Richter Bass RB2

Бренд: Laney Страницы: 16

Бренд: Laney Страницы: 24

Бренд: Laney Страницы: 6

Бренд: Xaoc Devices Страницы: 6

Бренд: Channel D Страницы: 8

Бренд: NJS Страницы: 8

Бренд: Pyle Pro Страницы: 2

Бренд: ORANGE Страницы: 13

Бренд: Audio Research Страницы: 8

Бренд: Carson Страницы: 12

EVID C8.2 Ceiling

Бренд: Electro-Voice Страницы: 2

Бренд: Wilson Electronics Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды