Lightware MX8x8DVI-HDCP-Pro Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 108

background image

MX32x32DVI-HDCP-Pro and HDMI-Pro

User’s Manual v1.0

Page 37/ 109

EDID switch

Source

Destination

EDID short name

This menu is used to select the emulated EDIDs on the inputs. You have to specify
the EDID source and the desired input port then press ENTER.

If you select an output port as source then dynamic routing will be performed: the
input will follow the changes of the output port. If there is no connected device on
the selected output, then the EDID of the last attached sink will be emulated.

Press the EDID button to exit this menu.

3.3.4. Signal Present mode

The selected input port numbers

The output ports

Signal present mode is active when Signal present button is illuminated. To enter
or exit from Signal present mode you have to press this button.

The  LCD  screen  shows  the  actual  connections  between  the  inputs  and  outputs.
The second line represents the output and  the first line represents the connected
inputs.  Only  8  connections  can  be  displayed  simultaneously.  If  your  matrix  has
greater I/O sizes, press the LEFT and RIGHT buttons to switch between the pages.

If you are in Signal Present mode, the source and destination buttons show the
actual state of the matrix. If a source button is illuminated then SCDT is present on
that source. If a destination button is illuminated then a powered display is attached
to this output (Hot Plug Detect signal is present). You can quickly check the cable
connections with this feature.

«
...
35
36
37
38
39
...
»

Содержание MX8x8DVI-HDCP-Pro













































































































Отзывы:

Нет отзывов

Похожие инструкции для MX8x8DVI-HDCP-Pro

Бренд: Nakamichi Страницы: 34

Бренд: Panasonic Страницы: 5

BeoLink Passive

Бренд: Bang & Olufsen Страницы: 12

Бренд: Dared Страницы: 4

Бренд: Yamaha Страницы: 19

Бренд: Madison Страницы: 51

Бренд: Advance acoustic Страницы: 11

Бренд: Pronomic Страницы: 16

SINGLE RECTIFIER RECT-O-VERB 50 2 Series

Бренд: Mesa/Boogie Страницы: 11

Бренд: Jolida Страницы: 17

Бренд: ZENEC Страницы: 30

1407A POWER AMPLIFIER

Бренд: Altec Lansing Страницы: 17

Бренд: Boss Audio Systems Страницы: 8

Бренд: Eden Страницы: 6

Бренд: AudioSource Страницы: 8

NAC 112 - ISSUE 2

Бренд: NAIM Страницы: 30

Бренд: Altinex Страницы: 10

Бренд: Texas Instruments Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды