Lighthouse solair 3100 Скачать руководство пользователя страница 93

Страница: 93 / 188

Operating Counter

248083389-1 Rev

6-27

ALARM

The Particle Alarm screen allows the user to enable alarming on
specific channels as shown in Figure 6-31.

Figure 6-31 Particle Alarm Configuration Example

Note:

Alarming is only

applicable for AUTO and
MANUAL mode. It applies
only to Raw particle counts
even if the instrument is
displaying Normalized
data.

If the instrument is set to
Differential data, the alarm
threshold will apply to the
differential counts.

If the instrument is set to
display Cumulative data,
the alarm threshold will
apply to the cumulative
counts.

To enable the alarming for any channel, press the "

" next to that

channel. When a checkmark is displayed, that channel is enabled for
alarming. Press the checkmark to disable the alarming for that channel.

Alarm Threshold

Press the threshold button next to the enabled channel in order to set the
alarm threshold for that channel. The Alarm Threshold screen will open
as shown in Figure 6-32.

Figure 6-32 Configure Alarm Threshold

Threshold Button

Содержание solair 3100





























































































































































































Результаты поиска

Содержание solair 3100

Отзывы:

Бренды по названию

Популярные бренды

Lighthouse solair 3100, Руководство по эксплуатации

Результаты поиска

Содержание solair 3100

Отзывы:

Бренды по названию

Популярные бренды