manualshive.com logo in svg

Lighthouse solair 3100, Руководство по эксплуатации

Поделиться
Скачать
Lighthouse solair 3100 Скачать руководство пользователя страница 149

Programming

248083389-1 Rev 

7-3

USB Communications

The SOLAIR provides point-to-point communications via the USB 
Port. 

If it hasn’t been done, yet, install the USB driver provided on the 
product CD. Once it has been installed and the instrument is connected, 
the driver will be used to establish communications using a virtual 
COM port on the PC. 

Using the USB Port to connect to a PC

To connect the instrument to a computer using the USB port, make sure 
that the driver has been installed first. Connecting the instrument to the 
PC and applying power before the driver has been installed will be 
problematic. Refer to the following: 

Note: 

Make sure the 

USB driver has been 
installed on the PC before 
connecting and applying 
power to the instrument.

1. Remove power from the instrument.

2. Connect Side B of a standard “A to B” USB cable (See Figure 7-2) 

to the instrument (only Side B will fit).

Figure 7-2  “A to B” USB Cable

3. Connect Side A to any available USB port on the PC.

4. Apply power to the instrument.

5. Windows will recognize that a new hardware device has been 

attached and will finalize the installation as needed. This is a 
routine “registering” of components that should take only a 
moment. An additional COM port will be added to the PC. 

Содержание solair 3100





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды