12
13
5. Remove the two SCREWS (9) securing the REAR CONSOLE COVER (10) to the frame. Remove the REAR CONSOLE
COVER. Remove the TOP INSERT (11) from the REAR CONSOLE COVER and discard. Set the REAR CONSOLE
COVER aside.
6. Console Cable Connections
For 95T Elevation Inspire Units Only:
6a.
Carefully pull the MEDIA CABLE BUNDLE
(12)
(Power and Coaxial)
from inside the
CONSOLE BRIDGE (13). Unbundle and
straighten the media cables.
6b.
Install the coaxial extension coupler and
coaxial
extension
cable.
6c.
Connect the I-R REMOTE CONTROL (A)
and
VIDEO
(B)
CABLES to the back of the
DISPLAY CONSOLE (C).
6d.
Tape the ends of all CABLES
(Power,
Coaxial, I-R Remote Control, Video)
together.
For 95T Elevation Discover SI Units Only:
Note:
Only the COAXIAL CABLE is inside the CONSOLE BRIDGE.
6a.
Attach the three MEDIA CABLES (12) to the back of the Discover SI CONSOLE (C) as shown below.
7. Hold the MAIN BRACKET ASSEMBLY (4) close to the CONSOLE BRIDGE (13). With the holes facing upward, feed
the taped end of the MEDIA CABLES (12) through the bottom of the main bracket assembly and out of the upper
hole. Carefully pull excess media cable through the main bracket assembly.
8. Slide one GROMMET (14) over the taped end of the MEDIA CABLES (12). Install the GROMMET into the top access
hole.
9. Tilt the MAIN BRACKET ASSEMBLY (4) upward and align the LOWER MOUNTING BRACKET (3) holes with those
in the console bracket posts. Secure the MAIN BRACKET ASSEMBLY using four SCREWS (5) and WASHERS (6).
Tighten the screws securely (8-10 ft. lbs.).
CAUTION:
Raise the BRACKET COVER (7) to meet the exiting MEDIA CABLES before mounting the MAIN BRACKET
ASSEMBLY.
C
A
B
13
12
14
4
6
5
11
10
9
C
14
4
6
5
11
10
9
12
13
Remote
High-Def
Treadmill Elevation Discover SI Console
Power
For Achieve Console Units Only:
a.
Remove the two SCREWS (A) and WASHERS (B)
securing
the
BOTTOM INSERT (C). Remove the
BOTTOM INSERT. Do not discard the SCREWS and
WASHERS.
b.
Locate the REMOTE CONTROL (D) and REMOTE
BRACKET (E). Feed the REMOTE CABLE (F)
through the large access hole in the REMOTE BRACKET
(E).
With
the
REMOTE CONTROL (D) and REMOTE
BRACKET
(E) oriented as shown, secure them together
using
one SCREW. (G) Tighten the screw securely.
c.
Carefully feed the REMOTE CABLE (F) through the open-
ing in the bottom of the CONSOLE (H) and through
the back of the console. Position the REMOTE BRACKET
(E) into position replacing the BOTTOM INSERT (C).
Secure
the
REMOTE BRACKET (E) using the previously
removed
SCREWS (A) and WASHERS (B).
10. With the remaining TV BRACKET (15) oriented as shown,
install it to the back of the ATTACHABLE TV (16) using
four SCREWS (17) and WASHERS (18). Tighten the screws
securely (8-10 ft. lbs.).
Note:
Be sure the side holes of the TV BRACKET are oriented as
shown.
11. Position the TV BRACKETS (8 & 15) together as shown and secure them together using one BOLT (18), WASHER
(19) and NUT (20). Leave the bolt and nut loose at this time.
Note:
Be sure the PIVOT POST of the TV BRACKET engages onto TV BRACKET (8).
H
16
D
A
A
C
B
16
E
F
G
A
A
B
21
15
16
18
19
22
4
8
20
7
10
16
15
17
18
Содержание ATV15-XXXA-02
Страница 1: ...1008767 0001 AA 15 ATTACHABLE TV ASSEMBLY INSTRUCTIONS ...
Страница 2: ......
