LG LT-C182QLE1 Скачать руководство пользователя

Страница: 35 / 38

Installation Manual

Installation

Function Code

Dry Contact
setting value

Select Dry contact setting by
pressing button.
(00 : Automatic, 01 : manual)

Press button to save.

If pressing button long for 3
seconds, it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters

into user setup mode. Please press
more than 3 seconds for sure.

If pressing button repeatedly, it moves to
remote controller dry contact mode setup
menu as picture below.

Pressing button will exit settings mode.

❈

After setup, it automatically gets out of

setup mode if there is no button input for
25 seconds.

❈

When exiting without pressing set button,

the manipulated value is not reflected.

Dry contact function is the function that is possible to use only when dry contact equipment is
separately purchased/setup.

•

Please refer to dry contact manual for more details.

▶

What is Dry Contact?
Like hotel card key and body perception sensor, it is the signal of the point of contact when
using air-conditioner by interlocking.

Installer Setting - Option Function Setting

Содержание LT-C182QLE1







































Результаты поиска

Содержание LT-C182QLE1

Отзывы:

Похожие инструкции для LT-C182QLE1

Бренды по названию

Популярные бренды

LG LT-C182QLE1, Руководство по установке

Результаты поиска

Содержание LT-C182QLE1

Отзывы:

Похожие инструкции для LT-C182QLE1

Бренды по названию

Популярные бренды