LG LT-C182QLE1 Скачать руководство пользователя

Страница: 32 / 38

Ceiling Cassette Air Conditioner

Installation

Function Code

Thermistor setting

Set Thermistor value by pressing
button. (01: Remote Controller,
02: Indoor, 03: 2TH)

Press button to save.

If moving to room temperature perception
sensor selection menu by pressing
button, it indicates as picture below.

If pressing button long for 3
seconds, it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters

into user setup mode. Please press
more than 3 seconds for sure.

Pressing button will exit settings mode.

❈

After setup, it automatically gets out of

setup mode if there is no button input for
25 seconds.

❈

When exiting without pressing set button,

the manipulated value is not reflected.

The function of 2TH has different operation characteristics according to the product.

Temperature sensor selection

Function

Remote controller

Operation in remote controller temperature sensor

Indoor unit

Operation in indoor unit temperature sensor

2TH

Cooling

Operation of higher temperature by comparing indoor unit's and wired remote
controllerʼs temperature.
(There are products that operate at a lower temperature.)

Heating

Operation of lower temperature by comparing indoor unit's and wired remote
controller's temperature.

<Thermistor Table>

This is the function to select the temperature sensor to judge the room temperature.

Installer Setting -Thermistor

Содержание LT-C182QLE1







































Результаты поиска

Содержание LT-C182QLE1

Отзывы:

Похожие инструкции для LT-C182QLE1

Бренды по названию

Популярные бренды

LG LT-C182QLE1, Руководство по установке

Результаты поиска

Содержание LT-C182QLE1

Отзывы:

Похожие инструкции для LT-C182QLE1

Бренды по названию

Популярные бренды