LG LT-C182QLE1 Скачать руководство пользователя

Страница: 33 / 38

Installation Manual

Installation

Function Code

Thermistor setting

Select ceiling height value by pressing
button. (01:Low, 02:Standard,
03:High, 04Very high)

Press button to save.

If moving to ceiling height selection menu by
pressing button, it indicates as picture
below.

If pressing button long for 3
seconds, it enters into remote
controller setter setup mode.
- If pressing once shortly, it enters

into user setup mode. Please press
more than 3 seconds for sure.

Pressing button will exit settings mode.

❈

After setup, it automatically gets out of

setup mode if there is no button input for
25 seconds.

❈

When exiting without pressing set button,

the manipulated value is not reflected.

This function is to adjust FAN Airflow rate according to ceiling height (For ceiling type product)

•

Ceiling height setting is available only for some products.

•

Ceiling height of ʻVery highʼ function may not exist depending on the indoor unit.

•

Refer to the product manual for more details.

Ceiling Height Level

Description

Low

Decrease the indoor airflow rate 1 step from standard level

Standard

Set the indoor airflow rate as standard level

High

Increase indoor airflow rate 1 step from standard level

Very high

Increase indoor airflow rate 2 steps from standard level

<Ceiling Height Selection Table>

Installer Setting -Ceiling Height Selection

Содержание LT-C182QLE1







































Результаты поиска

Содержание LT-C182QLE1

Отзывы:

Похожие инструкции для LT-C182QLE1

Бренды по названию

Популярные бренды

LG LT-C182QLE1, Руководство по установке

Результаты поиска

Содержание LT-C182QLE1

Отзывы:

Похожие инструкции для LT-C182QLE1

Бренды по названию

Популярные бренды