LG LS090HEV Скачать руководство пользователя страница 32

Страница: 32 / 86

Single Zone High Efficiency

, Standard, Extended Pipe and Mega W

all Mount Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

general inStallation guidelineS

Mounting the indoor unit to the installation Plate

Installation plate

Indoor unit

3”

Spacer

1. Hook the indoor unit onto the upper portion of the installation

plate ((1) Figure 21).

2. Engage the hooks at the top of the indoor unit with the upper

edge of the installation plate.

•

Ensure that the hooks are properly seated on the installation plate

by moving it left and right.

3. Move the bottom of indoor unit towards the installation plate to

anchor to wall ((2) Figure 21).

•

It helps to press the lower left and right sides of the unit against the

installation plate until the hooks engage into their slots.

•

You will hear a clicking sound as the bottom attaches to the instal-

lation plate successfully.

4. Finish by inserting and tightening two type “C” screws into the

bottom of the installation plate (Figure 23).

•

Pay attention to the positioning of the piping through any wall as

shown in the figure, as you insert the screws to the indoor unit.

Preparing for Piping/ Electrical Connection

1. To prepare indoor unit for piping, disengage bottom on indoor unit

from installation plate by reversing step 3 from previous

procedure.

•

This step will separate the indoor unit’s bottom side from the wall

mount in order to route drain hose correctly. See Figure 24 for a

reference of the rear view of the indoor unit.

2. Swing drain hose holder (L-bracket) out and anchor as shown in

Figure 22, against installation plate.

3. Optionally, go to

Refrigerant Piping Connections

section

of this manual to continue with piping connections to the indoor

unit.

4. Optionally, go to Electrical Connections section of this manual to

continue with conduit/electrical wiring to the indoor unit.

Figure 21: Mounting Unit on Installation Plate

Figure 22: Mounting Unit on Installation Plate

Figure 23: Mounting Bottom of Unit to Installation Plate

Figure 24: Rear View of IDU

side of the indoor unit from the wall .

Installation Plate

Drain Hose

Holder

L-bracket

Type 'C' Screws

Bottom of

Indoor Unit

Piping

Through

Wall

Installation Plate

Drain Hose

Drain Hose Holder

Mounting of Indoor Unit

Содержание LS090HEV























































































Результаты поиска

Содержание LS090HEV

Отзывы:

Похожие инструкции для LS090HEV

Бренды по названию

Популярные бренды

LG LS090HEV, Руководство по установке

Результаты поиска

Содержание LS090HEV

Отзывы:

Похожие инструкции для LS090HEV

Бренды по названию

Популярные бренды