LG LS090HEV Скачать руководство пользователя страница 82

Страница: 82 / 86

Single Zone High Efficiency

, Standard, Extended Pipe and Mega W

all Mount Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

trouBleSHooting

Error Codes

Table 33: Single Zone Wall Mounted Outdoor Unit Error Codes

Error

Code

Description

No. of Times Outdoor Unit

LEDs Blink

LED1

(Plasma LED)

LED2

(Power LED)

21 DC Peak (IPM Fault); Compressor DC voltage was too high

22 Current Transformer2 (CT2) error; Alternating current (AC) input too high

23 DC Link Low Volt

25 AC Low/High Volt

26 DC Comp Position Error (not providing rotation), Locking

27 PSC Fault; Current to inverter compressor between AC and DC converter circuit

too high

28 Inverter compressor DC voltage is too high

29 Inverter compressor amperage is too high

31 Current-to-current transformer (CT) thermistor is too low

32 Inverter Compressor Discharge Pipe (D-Pipe) Overheat

40 CT Sensor Error; Thermistor is disconnected or is shorted out

41 D-Pipe Sensor INV is disconnected or shorted out

44 Outdoor Air Sensor is disconnected or shorted out

45 Middle thermistor of outdoor unit condenser coil is disconnected or shorted out

46 Outdoor unit suction line thermistor is disconnected or shorted out

48 Outdoor unit coil outlet (liquid line) thermistor is disconnected or shorted out

53 Communication failure from outdoor unit to indoor unit

60 Outdoor unit printed circuit board (PCB) EEPROM check sum error

61 Outdoor unit condenser coil temperature is too high

62 Outdoor unit inverter compressor PCB heat sink temperature is too high

63 Condenser coil pipe thermistor temperature is too low

65 Heat sink thermistor has disconnected or has shorted out

67 Outdoor brushless direct current (BLDC) fan motor lock error

Single Zone Wall Mounted outdoor unit error codes

The Single Zone Wall Mounted outdoor unit error codes are visible on the outdoor unit, as well as, from the indoor unit. However, the indoor

unit error codes are only visible from the indoor unit and will not display at the outdoor unit. When troubleshooting the system, be sure to

verify if the error codes that are being displayed are specific for indoor or outdoor units.

Refer to Service Manuals posted on www.lghvac.com for a full description of all error codes and work-arounds.

Содержание LS090HEV























































































Результаты поиска

Содержание LS090HEV

Отзывы:

Похожие инструкции для LS090HEV

Бренды по названию

Популярные бренды

LG LS090HEV, Руководство по установке

Результаты поиска

Содержание LS090HEV

Отзывы:

Похожие инструкции для LS090HEV

Бренды по названию

Популярные бренды