LG LS090HEV Скачать руководство пользователя страница 22

Страница: 22 / 86

Single Zone High Efficiency

, Standard, Extended Pipe and Mega W

all Mount Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

general data

R410A Refrigerant

•

Piping wall thickness must comply with the applicable local, state, and federal codes for the 551 psi design

pressure of R410A.

•

Because R410A is a combination of R32 and R125, the required additional refrigerant must be charged in its liquid state. If the refrig-

erant is charged in its gaseous state, its composition changes and the system will not work properly.

r410a refrigerant

R410A refrigerant has a higher operating pressure in comparison to R22 refrigerant and, therefore, all piping system materials installed must

have a higher resisting pressure than the materials traditionally used in R22 systems.
R410A refrigerant is an azeotrope of R32 and R125, mixed at 50:50, so the ozone depletion potential (ODP) is 0. Many countries have

approved of and encouraged R410A for use as an environment friendly refrigerant.

•

To prevent the refrigerant cylinder from exploding, do not place it in direct sunlight.

•

Do not use any piping that has not been approved for use in high-pressure refrigerant systems.

•

To prevent the piping from softening, do not heat it more than necessary during installation.

Содержание LS090HEV























































































Результаты поиска

Содержание LS090HEV

Отзывы:

Похожие инструкции для LS090HEV

Бренды по названию

Популярные бренды

LG LS090HEV, Руководство по установке

Результаты поиска

Содержание LS090HEV

Отзывы:

Похожие инструкции для LS090HEV

Бренды по названию

Популярные бренды