6
To reduce the risk of fire, electric shock, or injury to persons when using
this appliance, follow basic precautions, including the following:
WARNING
READ ALL INSTRUCTIONS BEFORE USE
For your safety, the information in this manual must be followed to minimize the risk of
fire or explosion, electric shock, or to prevent property damage, injury to person, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of
least resistance for electric current. This appliance
must be equipped with a cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
person if you are in doubt as to whether the
appliance is properly grounded.
Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance must be connected to a grounded
metal, permanent wiring system or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment-
grounding terminal or lead on the appliance.
Electric shock can result if the dryer is not properly
grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
•
Properly ground dryer to conform with all
governing codes and ordinances.
Follow details
in the installation instructions. Electric shock can
result if the dryer is not properly grounded.
•
Before use, the dryer must be properly
installed as described in this manual.
Electric shock can result if the dryer is not
properly grounded.
•
Install and store the dryer where it will not be
exposed to temperatures below freezing or
exposed to the weather.
•
All repairs and servicing must be performed by
an authorized servicer unless specifically
recommended in this Owner’s Guide. Use only
authorized factory parts.
Failure to follow this
warning can cause serious injury, fire, electricl
shock, or death.
•
To reduce the risk of electric shock, do not
install the dryer in humid spaces.
Failure to
follow this warning can cause serious injury, fire,
electric shock, or death.
•
Connect to a properly rated, protected, and
sized power circuit to avoid electrical overload.
Improper power circuit can melt, creating electric
shock and/or fire hazard.
•
Remove all packing items and dispose of all
shipping materials properly.
Failure to do so
can result in death, explosion, fire, or burns.
•
Place dryer at least 18 in. above the floor for a
garage installation.
Failure to do so can result in
death, explosion, fire, or burns.
•
Keep all packaging from children.
Packaging
material can be dangerous for children. There is a
risk of suffocation.
WARNING
ヲ
Improper connection of
the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
WARNING
Содержание GDL1329CED3
