LG AHBW Series Скачать руководство пользователя страница 61

Страница: 61 / 81

System Set-Up

Installation Manual

ENGLISH

Emergency operation
• Definition of terms

Trouble :

a problem which can stop system operation, and can be resumed temporally under

limited operation without certificated professional's assist.

Error :

problem which can stop system operation, and can be resumed ONLY after certificated

professional's check.

Emergency mode :

temporary heating operation while system met trouble.

• Objective of introducing 'trouble'

- Not like airconditioning unit, Air-to-Water heat pump is generally operating in whole winter

season without any system stopping.

- If system found some problem, which is not critical to system operating for yielding heating

energy, the system can temporarily continue in emergency mode operation with end user's
decision.

• Classified trouble

- Trouble is classified two levels according to the seriousness of the problem : Slight Trouble and

heavy trouble

Slight trouble :

Sensor trouble.

Heavy trouble :

Compressor cycle trouble.

Option trouble :

a problem is found for option operation such as water tank heating. In this

trouble, the troubled option is assumed as if it is not installed at the system.

• Emergency operation level

- When system met trouble, it stops operation and wait for userʼs decision : Calling service center

or starting emergency operation.

- To start emergency operation, user simply push ON / OFF button once more.
- Two different levels are prepared for emergency operation : High temperature cycle and low

temperature cycle.

- In emergency operation mode, user can not adjust target temperature.

※ It can not be operated, if the electric heater accessory is not installed.

High temperature cycle OFF 50°C 24°C 70°C

Low temperature cycle ON 30°C 19°C 50°C

DIP

Switch

Target

Leaving Water

Temperature

Target

Room Air

Temperature

Target

Sanitary Water

Temperature

Содержание AHBW Series


















































































Результаты поиска

Содержание AHBW Series

Отзывы:

Похожие инструкции для AHBW Series

Бренды по названию

Популярные бренды

LG AHBW Series, Руководство по установке

Результаты поиска

Содержание AHBW Series

Отзывы:

Похожие инструкции для AHBW Series

Бренды по названию

Популярные бренды