LG AHBW Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 81

background image

Wiring and Water Piping for Unit

Installation Manual

37

ENGLISH

4. Wiring and Water Piping for Unit

Procedures about water piping and electric wiring are described in this chapter. Water piping and water
circuit connection, water charging, pipe insulations will be shown for water piping procedures.

Accessories connection, such as electric heater, sanitary water tank, thermostat, 3way or 2way valves, etc
will be dealt in separated chapter.

Electrical Wiring

Power cable is a cable which is used to supply external electricity to the unit. This cable is generally
connected between external power source (such as main electric power distribution panel of user's house)
and the unit.

Procedure for wiring to the unit is four steps. Before starting wiring, check if wire specification is suitable
and read following directions and cautions VERY carefully.

Wire specification

Power cable specification :

The power cord connected to the unit should be complied with IEC

60245 or HD 22.4 S4 (Rubber insulated cord, type 60245 IEC 66 or H07RN-F)

Round pressure terminal

Power wire

Terminal specification of power cable and related cautions :

Use round pressure terminals for connections to the power terminal block.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.

When none are available, follow the instructions below.
• Do not connect wiring of different thicknesses to the power terminal block. (Slack in the power

wiring may cause abnormal heat.)

• When connecting wiring which is the same thickness, do as shown in the figure below.

20mm

GN/YL

1 Phase(Ø)

«
...
35
36
37
38
39
...
»

Содержание AHBW Series


















































































Отзывы:

Нет отзывов

Похожие инструкции для AHBW Series

Бренд: Kaden Страницы: 24

Elite Big PAC-i S-200PE3E5B

Бренд: Panasonic Страницы: 316

Бренд: Toyotomi Страницы: 38

Бренд: Argo Страницы: 38

AirCon ServiceCenter

Бренд: Waeco Страницы: 76

Бренд: Daikin Страницы: 84

Бренд: thermital Страницы: 24

Бренд: Sencor Страницы: 21

Бренд: Argo Страницы: 52

ArcticAire APA070B1G

Бренд: Danby Страницы: 26

Бренд: Mach Power Страницы: 14

Ecolight 12000 UI

Бренд: Argo Страницы: 32

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 4

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды