LG AHBW Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 81

background image

Accessories Installation

46

Air-to-Water Heat Pump

General information

supports following thermostats.

Yes

Heating / Cooling (4)

Yes

Heating / Cooling (4)

Yes

Heating Only (3)

1 Ø 230 V

Electrical

(2)

Yes

Heating Only (3)

1 Ø 230 V

Mechanical

(1)

Supported

Operating Mode

Power

Type

(1) There is no electric circuit inside the thermostat and electric power supply to the thermostat is not

required.

(2) Electric circuit such as display, LED, buzzer, etc is included in the thermostat and electric power supply

is required.

(3) Thermostat generates "Heating ON or Heating OFF" signal according to user"s heating target

temperature.

(4) hermostat generates both "Heating ON or Heating OFF" and "Cooling ON or Cooling OFF" signal

according to user"s heating and cooling target temperature.

Choosing heating / cooling thermostat

• Heating / cooling thermostat must have "Mode Selection" feature to distinguish operation mode.
• Heating / cooling thermostat must be able to assign heating target temperature and cooling target

temperature differently.

• If above conditions are not kept, the unit can not operation properly.
• Heating / cooling thermostat must send cooling or heating signal immediately when temperature

condition is satisfied. No delay time while sending cooling or heating signal is permitted.

«
...
44
45
46
47
48
...
»

Содержание AHBW Series


















































































Отзывы:

Нет отзывов

Похожие инструкции для AHBW Series

Бренд: TCL Страницы: 28

Бренд: Galanz Страницы: 30

Бренд: Jaga Страницы: 12

Бренд: Samsung Страницы: 12

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 295

AW07A(G)2NBA/DE/EA

Бренд: Samsung Страницы: 16

Бренд: Rheem Страницы: 28

Бренд: Argo Страницы: 15

1PAMSH09-SZO-14.5

Бренд: Perfect Aire Страницы: 12

Бренд: Vertiv Страницы: 44

Бренд: Guzzanti Страницы: 140

Бренд: Daikin Страницы: 18

Бренд: Hisense Страницы: 31

Бренд: dirna Bergstrom Страницы: 84

Бренд: thermital Страницы: 24

Бренд: Hisense Страницы: 51

Бренд: AlpicAir Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды