Lexmark Optra E310 страница 100 Скачать руководство пользователя

Страница: 100 / 116

Appendix D: Notices

Notices

Electronic emissions notices

Federal Communications Commission (FCC)
compliance information statement

The Optra E laser printer, type 312, has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause

undesired operation.
The FCC Class B limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harm-

ful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the fol-

lowing measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•

Consult your point of purchase or service representative for

additional suggestions.

The manufacturer is not responsible for any radio or television interfer-

ence caused by using other than recommended cables or by unautho-

rized changes or modifications to this equipment. Unauthorized changes

or modifications could void the user’s authority to operate this equip-

ment.
To assure compliance with FCC regulations on electromagnetic interfer-

ence for a Class B computing device, use a properly shielded and

grounded cable such as Lexmark part number 1329605 for parallel and

12A2405 for USB. Use of a substitute cable not properly shielded and

grounded may result in a violation of FCC regulations.

Any questions regarding this compliance information statement should

be directed to:
Director of Lab Operations

Lexmark International, Inc.

740 New Circle Road NW

Lexington, KY 40550

(606) 232-3000

Industry Canada compliance statement

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Avis de conformité aux normes d’Industrie
Canada

Cet appareil numérique de la classe B respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

European Community (EC) directives conformity

This product is in conformity with the protection requirements of EC

Council directives 89/336/EEC and 73/23/EEC on the approximation

and harmonization of the laws of the Member States relating to electro-

magnetic compatibility and safety of electrical equipment designed for

use within certain voltage limits.
A declaration of conformity with the requirements of the Directive has

been signed by the Director of Manufacturing and Technical Support,

Lexmark International, S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety require-

ments of EN 60950.

LA.bk Page 87 Thursday, February 8, 2001 2:19 PM

Содержание Optra E310





















































































































Результаты поиска

Содержание Optra E310

Отзывы:

Похожие инструкции для Optra E310

Бренды по названию

Популярные бренды

Lexmark Optra E310, Руководство пользователя

Результаты поиска

Содержание Optra E310

Отзывы:

Похожие инструкции для Optra E310

Бренды по названию

Популярные бренды