Lexmark 2480 - Forms Printer B/W Dot-matrix Скачать руководство пользователя страница 66

Страница: 66 / 170

4-6

Service Manual

24xx

Covers, Front Removal

1. Rotate the front cover out and up about three inches from the

bottom of the printer.

2. Push the front cover up and out of the printer.

Covers, Ribbon Access Removal

1. Pull both gray spring loaded ribbon access cover release

latches [A], on either side of the ribbon access cover, up toward
the front of the printer.

2. Lift the ribbon access cover up and out of the printer.

Note: When replacing the ribbon access cover, be sure to hook the
front hinge points on either side of the ribbon access cover first and
lower the cover into place. Be sure that both gray spring loaded
ribbon access cover latches snap and lock.

Содержание 2480 - Forms Printer B/W Dot-matrix











































































































































































Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды

Lexmark 2480 - Forms Printer B/W Dot-matrix, Руководство по обслуживанию

Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды