Lexmark 2480 - Forms Printer B/W Dot-matrix Скачать руководство пользователя страница 24

Страница: 24 / 170

2-6

Service Manual

24xx

Abnormal Print Operation Problems

Auto Sheet Feeder Problems

Symptom

Action

Printer will not print,
or become ready.

Abnormal operation,
incorrect characters,
or incorrect line
width.

Printer is ready but
will not print from the
computer correctly.

Undefined or
incorrect
character(s).

Be sure the interface cable is connected properly.

Go to

“No Print or Abnormal Print Service

Check” on page 2-21

Slow printing speed.

Go to

“Print Speed Service Check” on

page 2-28

Symptom

Action

Auto sheet feeder
will not feed paper.

Auto sheet feeder
double feeds.

Auto sheet feeder
has intermittent feed
problems.

Be sure Sheet Feed is enabled in the Setup Mode.

Be sure the paper select lever is in the cut sheet
position.

Go to

“Auto Sheet Feeder (ASF) Service

Check” on page 2-14

Содержание 2480 - Forms Printer B/W Dot-matrix











































































































































































Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды

Lexmark 2480 - Forms Printer B/W Dot-matrix, Руководство по обслуживанию

Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды