Lexmark 2480 - Forms Printer B/W Dot-matrix Скачать руководство пользователя страница 27

Страница: 27 / 170

Diagnostic Information

2-9

24xx

Power Problems

Lower feed roll shaft
rotates, but paper
does not feed.

Pressing FormFeed
does not feed paper.

Abnormal noise
created while
feeding.

Paper jams, skews
or creases.

Incorrect or no line
spacing: wider,
narrower, or
overlapping lines.

Push/Pull Tractor
does not work.

Be sure the paper select lever is in the correct
position.

Go to

“Paper Feed Service Check” on

page 2-23.

Incorrect Top of
Form positioning.

Go to

“Top-Of-Forms Service Check” on

page 2-32

Symptom

Action

When the power
switch is on, the
Power light does not
turn on or the printer
does not start.

The Power light
blinks or changes
intensity.

Check continuity of the power cord and the voltage
of the user’s outlet.

Go to

“Power Service Check” on page 2-27.

Symptom

Action

Содержание 2480 - Forms Printer B/W Dot-matrix











































































































































































Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды

Lexmark 2480 - Forms Printer B/W Dot-matrix, Руководство по обслуживанию

Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды