Lexmark 2480 - Forms Printer B/W Dot-matrix Скачать руководство пользователя страница 53

Страница: 53 / 170

Diagnostic Information

2-35

24xx

3 Beeps and Tractor 2 LED blinks 3 times

Tractor 2 selected from operator panel but printer does not detect Tractor 2
or detects that the Tractor 2 mechanism is not installed.

FRU

Action

Tractor 2
Board/Cable Asm.

Check the Tractor 2 in-place sensor or the
cable connection.

The in-place sensor actuator extends through
the Tractor 2 cover and rests on the printer
cover when Tractor 2 is installed.

Remove the Tractor 2 cover and be sure the in-
place sensor opens when the Tractor 2 is
installed. The voltage at Tractor 2 CN1-13
should be +5 V dc with the sensor open and 0
with it closed.

Replace the Tractor 2 board/cable assembly if
the sensor signal is wrong.

For information on the Tractor 2 cable
connectors, see

“Tractor 2 Cable

Connectors” on page 5-26

Logic Board

Check the cable connection from Tractor 2 to
the printer.

If possible, try the Tractor 2 with another printer
to determine if the problem is the Tractor 2
board/cable assembly or the printer logic
board.

Содержание 2480 - Forms Printer B/W Dot-matrix











































































































































































Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды

Lexmark 2480 - Forms Printer B/W Dot-matrix, Руководство по обслуживанию

Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды