background image

Diagnostic Information

2-5

24xx

Symptom Check Table

1. Select the symptom that best describes the problem.

2. Perform the appropriate action before you go to the indicated 

service check.

Abnormal Indications

Abnormal Noise Problems

Symptom

 Action 

7 or more lights turn 
on but do not turn 
off. 

The Power light is 
on, but POST will 
not run.

Disconnect the interface cable from the printer and 
turn the printer off and then on. If POST now runs 
correctly, the problem is in the computer or 
interface cable.

Go to 

“POST Service Check” on page 2-26.

Symptom

Action

During POST, 
abnormal noise 
comes from the 
carrier.

Check the ribbon cartridge for binds or damage.

Go to 

“Carrier Service Check” on page 2-16

.

During idling, 
abnormal noise 
comes from the 
printer.

When feeding paper, 
abnormal noise is 
created. 

During printing or 
POST, abnormal 
noise is created.

Go to 

“Abnormal Noise Service Check” on 

page 2-13.

Содержание 2480 - Forms Printer B/W Dot-matrix











































































































































































Отзывы: