Lexmark 2480 - Forms Printer B/W Dot-matrix Скачать руководство пользователя страница 87

Страница: 87 / 170

Repair Information

4-27

24xx

Printhead Removal

1. Turn the printer off.

2. Disconnect the power cord at the printer and allow the printhead

to cool for 15 minutes, prior to handling.

3. Set the form thickness lever to position 7.

4. Remove the ribbon access cover. Go to

“Covers, Ribbon

Access Removal” on page 4-6

5. Remove the ribbon cartridge.

6. Squeeze the printhead latches together while pulling the

printhead up and out of the printer.

7. Disconnect the printhead cable(s) from the printhead.

Reassembly Note: Be sure the printhead cables are correctly
aligned and secured. Be sure to perform the Printhead-to-Platen
Gap Adjustment procedure. Go to

“Printhead-to-Platen Gap

Adjustment” on page 4-2

Printhead Cables Removal

WARNING: Be careful not to damage the printhead cable(s) as they
are secured with double-sided adhesive tape.

1. Remove the top cover. Go to

“Covers, Top Removal” on

page 4-8

2. Remove the printhead. Go to

“Printhead Removal” on

page 4-27

3. Release the printhead cables from the flexible cable holders.

4. Disconnect the printhead cables from the logic board.

Note: Be sure the printhead cables are correctly aligned and
secured. They must be flat, with no twists.

Содержание 2480 - Forms Printer B/W Dot-matrix











































































































































































Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды

Lexmark 2480 - Forms Printer B/W Dot-matrix, Руководство по обслуживанию

Результаты поиска

Содержание 2480 - Forms Printer B/W Dot-matrix

Отзывы:

Похожие инструкции для 2480 - Forms Printer B/W Dot-matrix

Бренды по названию

Популярные бренды