Quick operation instruction of the LX-HS03 system basic configure
Open the main, connect the standby power in the main and switch on power by AC power adapter. Here the
main
’
s POWER,AWAY LED light and the numeric LED display counting down time 9,8,7
…
1, and after 1 DI sound
you can operate the main.
1.Outer device accession operation
1.1 remote controller
’
s original accession
The system can access 4 remote controllers for operation. Press* key and then input operation password (when
out factory, the password is 0000), press SET to enter the setting mode. Press the function channel key
”
4
”
, and then
input the first remote controller channel----
“
1
”
and then press # key, within 60sec press the remote controller
’
s key,
the main will give
“
DI
”
sound, which indicate the main have accept it. Repeat pressing CE key until
“
DIDI
”
sound is
heard to exit the setting mode. So the accession of the first remote controller has finished. By the means same as
above, you only need input remote controller channel
“
2
”
/
”
3
”
/
”
4
”
, the second/third/ fourth remote controller can be
accessed. At last you can repeat pressing CE key until
“
DIDI
”
sound is heard to exit the setting mode. And then the
remote controller can control the main.
1.2 medical for help accession
1.2.1 the remote controller
“
+
”
is designed to medical for help. It
’
s function channel is
“
2
”
same as other outer
wireless device;
1.2.2 press * key, input operation password 0000, and then press SET key to enter the setting mode. Press function
channel key
”
2
”
and then select a numeral as the one that the main
’
s numeric LED display when it emit signal. For
example: press 0 and then press # key, then press the remote controller
’
s
“
+
”
key, the main give
“
DI
”
sound, which
indicate the main accept it, and then repeat pressing CE key until
“
DIDI
”
sound is heard to exit the setting mode.
Then test the medical for help remote controller to ensure that it has been accepted in deed by the main.
1.3.other outer wireless device
’
s accession
1.3.1 wireless PIR device
’
s accession
According to the section 1.2.2 enter the function channel 2, select the numeral key that you didn
’
t select
forestall, and then select position key. For example: for the indoor detector select key, the outdoor
detector select key. and then switch on the internal power of the wireless PIR detector, here the wireless
PIR detector will emit a signal to the main. After it receives this signal, the main give
”
DI
”
sound, which indicate
the main accept it. And then repeat pressing CE key until
“
DIDI
”
sound is heard to exit the setting mode. Then
test the PIR detector, the main should alarm.
Attention: after you access any detector, you should test it to
ensure every detector has been accepted by the main.
1.3.2 the magnetism
’
s accession
The magnetism
’
s accession is same as the section 1.3.1, only the numeral you select is different.
2.the function channel code of the outer device on the main.
4-key remote controller Wireless PIR detector Door magnetism Medical for help remote controller
Function channel code is
“
4
”
function channel code is
“
2
”
3. Telephone dial-up function setting
3.1 press * key, input operation password 0000, and then press SET key to enter the setting mode. Press function
channel key
”
1
”
, and then select
“
1
”
(the 1
st
group, that mean you will save the first group phone number you want
dial), input the phone number, for example:8726398, and then press # key to confirm. Then repeat pressing CE key
until
“
DIDI
”
sound is heard to exit the setting mode. And then you can test its dial-up function by pressing the key of
the medical for help remote controller or sense the PIR detector. The 2
nd
/3
rd
/4
th
group number saving is same as
above, you need only select the
“
2
”
(the 2
nd
group) /
“
3
”
(the 3
rd
group)/
“
4
”
(the 4
th
group) and then input the
needed number, press #key to confirm and then repeat pressing CE key until
“
DIDI
”
sound is heard to exit the
setting mode. We suggest you should test its dial-up function after setting every time.
★★★
Please attention: Due to the different installation position and distance (because the wireless
transmission signal is obstructed), you should test them after installation to ensure all detectors and
remote controllers can work normally. Only that can show installation is successful.
If you need use other functions of the system, please read carefully
following instructions
！
