LevelOne FCS-5051 Скачать руководство пользователя страница 64

Страница: 64 / 102

5.3.3.13 Storage Management (Local Recording)

The Storage Management setting can be found under this path: System> Storage

Management.

Users can implement local recording to the Micro SD/SDHC card up to 32GB. This page

shows the capacity information of the Micro SD card and a recording list with all the

recording files saved on the memory card. Users can also format the SD card and implement

automatic recording cleanup through the setting

page.

To implement Micro SD card recording, please go to the <Recording> page (refer to

Recording) for activation.

NOTE:

Please format the Micro SD/SDHC card when using for the first time.

Formatting will also be required when a memory card already being used on one

camera and later transferred to another camera with different software platform.

Содержание FCS-5051







































































































Результаты поиска

Содержание FCS-5051

Отзывы:

Похожие инструкции для FCS-5051

Бренды по названию

Популярные бренды

LevelOne FCS-5051, Руководство пользователя

Результаты поиска

Содержание FCS-5051

Отзывы:

Похожие инструкции для FCS-5051

Бренды по названию

Популярные бренды