LevelOne FCS-5051 Скачать руководство пользователя страница 69

Страница: 69 / 102

5.3.3.16.2 User Information

The User Information function can be found under this path: System> User Information.

The Administrator can view each added user’s login information and privileges (refer to

Security

Get User Information

All the users in the network will be listed in the <User information> zone as shown below:

User: 4321
It indicates that one user’s login username is “User”, and the password is

“

4321”.

Get User Privacy

Click on <get user privacy> at the bottom of the page, and the Administrator can view each

user

’s privileges as shown below:

User: 1:1:0:1

1:1:0:1= I/O access : Camera control : Talk : Listen (refer to Security)

Therefore, it denotes the user is granted privileges of I/O access, Camera control and Listen.

Содержание FCS-5051







































































































Результаты поиска

Содержание FCS-5051

Отзывы:

Похожие инструкции для FCS-5051

Бренды по названию

Популярные бренды

LevelOne FCS-5051, Руководство пользователя

Результаты поиска

Содержание FCS-5051

Отзывы:

Похожие инструкции для FCS-5051

Бренды по названию

Популярные бренды