LevelOne FCS-5051 Скачать руководство пользователя страница 59

Страница: 59 / 102

is from 1 to 99 minutes.

Triggered Action (Multi-option)

The Administrator can specify alarm actions that will take when network failure is detected.

All options are listed as follows:



Enable Alarm Output

Select the item to enable alarm relay output.



Record Stream to SD Card

Select the item and the alarm-triggered recording will be saved into your Micro SD card.

Pre-trigger buffer recording function allows users to check what happened to cause the

trigger. The pre-trigger buffer time range is from 1 to 3 seconds. Select <Upload for __

sec> to set the recording duration after alarm is triggered. The setting range is from 1 to

99999 seconds. Select <Upload during the trigger active> to record the triggered video

until the trigger is off.

NOTE:

Please make sure the local recording (with Micro SD/SDHC card) is

activated so that this function can be implemented. Refer to Recording for

further details.



Send Alarm Message by FTP/E-Mail

The Administrator can select whether to send an alarm message by FTP and/or E-Mail

when an alarm is triggered.

Save

Click on the <Save> button to save all the settings mentioned above.

Содержание FCS-5051







































































































Результаты поиска

Содержание FCS-5051

Отзывы:

Похожие инструкции для FCS-5051

Бренды по названию

Популярные бренды

LevelOne FCS-5051, Руководство пользователя

Результаты поиска

Содержание FCS-5051

Отзывы:

Похожие инструкции для FCS-5051

Бренды по названию

Популярные бренды