Let's Go Aero BLACK BOX Скачать руководство пользователя страница 13

Страница: 13 / 21

PAGE 13 OF 21

STEP 23

[Figure 25]

[Figure 35]

Remove the Washer and Nut supplied on the

back side of the remaining LED Light [

On the drivers side of the vehicle

, mount the

LED Light [

] with two License Plate Brackets

[

] on either side of the LED Mount Bracket

[

] using the supplied Phillips Screw on the

LED Light.

Secure the LED Light [

] and License Plate

Brackets [

] to the LED Mount Bracket [

]

by re-attaching the supplied Washer and Nut

onto the back of the LED Lights and LED Mount

Bracket [Figure 35].

Supplied LED Hardware

TOOLS: 7MM WRENCH & PHILLIPS HEAD SCREW DRIVER

Failure to properly connect the Yellow Wire to the drivers side of the vehicle and the Green Wire to the passenger

side of the vehicle will result in mismatched stop/turn lights and improper signaling.

WARNING:

STEP 24 (OPTIONAL)

STEP 25

Secure (user supplied) License Plate to the

License Plate Brackets [

] using two (2) 6mm

Hex Bolts [

], two (2) 6mm Washers [

] and

two (2) Nylon Nuts [

] [Figure 36].

Connect the Yellow Wire from the LED Lights [

] on the drivers side to the Yellow wire on the LED Wire Harness [

Connect the Green Wire from the LED Lights [

] on the passenger side to the Green wire on the LED Wire Harness

[

Weave the Wire Harness [

] in a straight path underneath the carrier and connect the Wire Harness 4-Flat connector to

the tow vehicles trailer light connections.

OPTIONAL

TIP:

Wrap the connection ends with Electrical Tape to help ensure

longevity of the wires.

TT
SS

[Figure 36]

TOOLS: TWO (2) 7/16 WRENCH OR SOCKET

OPTIONAL TOOL: ELECTRICAL TAPE

Содержание BLACK BOX






















Результаты поиска

Содержание BLACK BOX

Отзывы:

Бренды по названию

Популярные бренды

Let's Go Aero BLACK BOX, Руководство по эксплуатации продукта

Результаты поиска

Содержание BLACK BOX

Отзывы:

Бренды по названию

Популярные бренды