background image

Page 6 of 13

STEP 10  

Passenger

Driv

er

[Figure 19]

D

E

GEARSPACE:

 Install using 

the 

holes 

closest to the end 

of the Right & Left Support 

Bars 

[

D & E

] [Figure 18 & 

20]

.

GEARDECK:

 Install using 

the 

2nd holes from the 

edge of the Right & Left 

Support Bars 

[

D & E

[Figure 18 & 21].

Re-attach the hardware 

removed from Step 9 back 

in place installing with it 

the Right & Left [

D & E

assembly bar as shown 

fully installed [Figure 19].

A

[Figure 18]

1st Hole 

GearSpace

2nd Hole

GearDeck

D & E

Passenger

Driv

er

[Figure 20]

C

A

GearSpace

C

A

GearDeck

[Figure 21]

STEP 11 

Following the same procedure as Step 9 using the Legs [

A

] that face towards the vehicle, remove two (2) existing Leg 

Bolts located closest to the vehicle and the associated Hardware from each leg.

Install the Long Support Bar [

C

] by first re-installing one (1) existing Leg Bolt and hardware back though the 

hole 

on the 

Long Support Bar for each Leg. 

On the 

Slotted 

ends of the bar, use one (1) 1/4”-20 x 

3/4” Bolt [

P

], one (1) 1/4” Washer [

N

], and one (1) 1/4” 

Nylock Nut [

M

]

 

on each Leg to fully secure each legs as 

shown.

 

[Figure 22, 23, & 24].

SHOWN WITHOUT CARRIER FOR CLARITY

[Figure 24]

C

C

P

P

N

M

C

Slot

A

A

[Figure 22]

[Figure 23]

TOOLS REQUIRED: 9/16IN SOCKET & WRENCH, 7/16IN SOCKET & WRENCH, 

Hole

Leg

Hardware

LEG BOLT

LEG BOLT

TOOLS REQUIRED: 9/16IN SOCKET & WRENCH

Содержание H00550














Отзывы: