background image

Page 3 of 13

Passenger

Driv

er

For installation on GearSpace and GearDeck 

Cargo Carriers, the Landing Gear assembly 

uses the 

existing hardware

 already located on 

the floor of the carrier.  

TIP:

 

Bolt hole alignment of the Channels 

[B] to the carrier is a precision fit with the 

carriers frame mount. 

Realignment of the steel cross rails may 

be necessary. Loosen the Hat Brackets 

underneath the carrier and all floors bolts 

to adjust [Figure 5]. Be sure to only fully 

remove bolts for each leg installation 

needed. DO NOT REMOVE ALL BOLTS AT 

ONE TIME.

Remove two (2) bolts and their associated 

washers and nuts starting in the areas 

closest 

to the passenger side of the carrier

 [Figure 6]. 

[Figure 6]

[Figure 5]

Existing

Hardware

GENERIC CARRIER WITH SMOOTH 

FLOOR SHOWN FOR CLARITY

Existing

Hardware

STEP 4 

STEP 3 

Using the open 

SLOTS

 on each end of the 

[

A

] channel, Install one (1) Leg Assembly 

using the two (2) bolts and hardware 

removed from the carrier in Step 3.  [Figure 

7]. 

NOTE:

 This Leg [

A

] MUST be placed so that 

the 

wheel faces away from the vehicle

 as 

shown [Figure 8].

Passenger

Driv

er

Passenger

Driv

er

[Figure 8]

[Figure 7]

A

B

A

B

GENERIC CARRIER WITH SMOOTH 

FLOOR SHOWN FOR CLARITY

Existing

Hardware

TOOLS REQUIRED: 7/16IN SOCKET & WRENCH

TOOLS REQUIRED: 7/16IN SOCKET & WRENCH

Existing

Hardware

J

Existing

Hardware

Содержание H00550














Отзывы: