Lenovo 30CY Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 224

Lenovo 30CY Скачать руководство пользователя страница 80

Recovering from a BIOS update failure

To recover from a BIOS update failure, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See Chapter 9 “Hardware removal and installation” on page 97.

3. Locate the Clear CMOS /Recovery jumper on the system board. See “Hardware locations” on page 29.

4. Remove any parts and cables that impede your access to the Clear CMOS /Recovery jumper.

5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin

3).

6. Reinstall the parts and cables that were removed.

7. Reinstall the computer cover and reconnect any cables that were disconnected. See Chapter 9

“Hardware removal and installation” on page 97.

8. Turn on the computer and insert the BIOS update disc into the optical drive. Wait a few minutes. The

recovery process begins. After the recovery process is completed, your computer will shut down
automatically.

Note:

If the computer does not start up from the disc, select the disc as the startup device. See

“Selecting a temporary startup device” on page 70.

9. Repeat steps 1–4.

10. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).

11. Repeat step 6 and step 7.

12. Turn on the computer and the monitor. When the logo screen is displayed, press F1 or Fn+F1.

13. To prevent data loss, ensure that BIOS settings are restored to an earlier point.

Configuring RAID

This chapter provides information about how to configure Redundant Array of Independent Disks (RAID) for
your computer.

An Introduction to RAID

RAID is a technology that provides increased storage functions and reliability through redundancy.

When a group of independent physical storage drives is set up to use RAID technology, they are in a RAID
array. This array distributes data across multiple storage drives, but the array appears to the host computer
as one single storage unit. Creating and using RAID arrays provides high performance, such as the expedited
I/O performance, because several drives can be accessed simultaneously.

RAID drive groups configured according to certain RAID levels also improve data storage reliability and fault
tolerance compared with single-drive storage systems. Data loss resulting from a drive failure can be
prevented by reconstructing missing data from the remaining drives.

Note:

For RAID 0, the missing data resulting from a drive failure cannot be reconstructed.

RAID Level

Your computer must have the minimum number of SATA storage drives installed for the supported level of
RAID below:

• RAID 0: striped disk array

72

P330 Hardware Maintenance Manual

«
...
78
79
80
81
82
...
»

Содержание 30CY

































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды