Lenovo 30CY Скачать руководство пользователя страница 192

Страница: 192 / 224

4. Lift the clip on the rear of the flex module, and then slide the flex module cover to the rear of the flex

module.

Figure 168. Removing the flex module cover

5. To remove a front Thunderbolt I/O adapter, do the following:

a. Disconnect all the cables from the front Thunderbolt I/O adapter.

b. Pull the clip as shown to remove the front Thunderbolt I/O adapter and the retaining bracket out of

the flex module.

Figure 169. Removing the front Thunderbolt adapter and the retaining bracket out of the flex module

c. Flex the four clips on the sides of the retaining bracket to remove the front Thunderbolt I/O adapter

from the bracket.

Figure 170. Removing the front Thunderbolt I/O adapter from the retaining bracket

6. To install a new front Thunderbolt I/O adapter, do the following:

184

P330 Hardware Maintenance Manual

Содержание 30CY

































































































































































































































Результаты поиска

Содержание 30CY

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 30CY, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 30CY

Отзывы:

Бренды по названию

Популярные бренды