manualshive.com logo in svg

Lenovo 30CY, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo 30CY Скачать руководство пользователя страница 207

Appendix C. Regulatory information of countries and regions

The latest compliance information is available at:  

https://www.lenovo.com/compliance

Export classification notice

This product is subject to the United States Export Administration Regulations (EAR) and has an Export 
Classification Control Number (ECCN) of 5A992.c. It can be re-exported except to any of the embargoed 
countries in the EAR E1 country list.

Electronic emissions notices

Federal Communications Commission Declaration of Conformity

The following information refers to Lenovo personal computer machine types 30CY, 30D0, and 30D3.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult an authorized dealer or service representative for help.

Lenovo is not responsible for any radio or television interference caused by using other than recommended 
cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized 
changes or modifications could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 
this device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.

Responsible Party:
Lenovo (United States) Incorporated
7001 Development Drive
Morrisville, NC 27560
Email: [email protected]

Industry Canada compliance statement

CAN ICES-3(B)/NMB-3(B)

© Copyright Lenovo 2018, 2020

199

Содержание 30CY

































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды