Lenovo 30CY Скачать руководство пользователя страница 189

Страница: 189 / 224

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 187.

eSATA connector or IEEE 1394 connector

To remove or install an eSATA connector or an IEEE 1394 connector in the flex module, do the following:

1. Prepare your computer. See “Preparing your computer” on page 98.

2. Do either of the following:

• Disconnect the eSATA connector cable from the eSATA/SATA connector on the system board.

• Disconnect the IEEE 1394 cable from the IEEE 1394 adapter.

3. Remove the flex module out of the chassis. See “Device in the flex bay” on page 117.

4. Lift the clip

on the rear of the flex module and slide the flex module cover to the rear to remove the

cover.

Figure 164. Removing the flex module cover

Chapter 9

Hardware removal and installation

181

Содержание 30CY

































































































































































































































Результаты поиска

Содержание 30CY

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 30CY, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание 30CY

Отзывы:

Бренды по названию

Популярные бренды