Lenovo 30BG Скачать руководство пользователя страница 53

Страница: 53 / 146

Note:

If you want to update the BIOS from a flash update disc, the installation instructions might not

provide the instructions on how to record the update disc.

Recovering from a BIOS update failure

To recover from a BIOS update failure, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover.

3. Locate the Clear CMOS /Recovery jumper on the system board. .

4. Remove any parts and cables that impede your access to the Clear CMOS /Recovery jumper.

5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin

3).

6. Reinstall the parts and cables that were removed.

7. Reinstall the computer cover and reconnect any cables that were disconnected.

8. Turn on the computer and insert the BIOS update disc into the optical drive. Wait a few minutes. The

recovery process begins. After the recovery process is completed, your computer will shut down
automatically.

Note:

If the computer does not start up from the disc, select the disc as the startup device.

9. Repeat steps 1–4.

10. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).

11. Repeat step 6 and step 7. Then, turn on your computer.

Configuring RAID

This chapter provides information about how to configure Redundant Array of Independent Disks (RAID) for
your computer.

RAID Level

Your computer must have the minimum number of SATA hard disk drives installed for the supported level of
RAID below:

• RAID Level 0 – Striped disk array

– Two hard disk drives minimum

– Better performance without fault tolerance

• RAID Level 1 – Mirrored disk array

– Two hard disk drives minimum

– Improved read performance and 100% redundancy

To install a secondary hard disk drive, refer to “Secondary hard disk drive” on page 101.

Configuring the system BIOS to enable SATA RAID functionality

This section describes how to configure the system BIOS to enable SATA RAID functionality.

Note:

Use the arrow keys on the keyboard to make selections.

Chapter 5

Advanced configuration

Содержание 30BG



















































































































































Результаты поиска

Содержание 30BG

Отзывы:

Lenovo 30BG, Руководство пользователя, Страница: 53 / 146

Результаты поиска

Содержание 30BG

Отзывы: