Lennox SIGNATURE SLP99UH070XV36B Скачать руководство пользователя

Страница: 46 / 84

Page 46

III-PLACEMENT AND INSTALLATION

All pipe, fittings, primer and solvent cement must conform

with American National Standard Institute and the Ameri-

can Society for Testing and Materials (ANSI/ASTM) stan-

dards. The solvent shall be free-flowing and contain no

lumps, undissolved particles or any foreign matter that ad-

versely affects the joint strength or chemical resistance of

the cement. The cement shall show no gelation, stratifica

tion, or separation that cannot be removed by stirring. Re-

fer to TABLE 21 for approved piping and fitting materials

TABLE 21

PIPING AND FITTINGS SPECIFICATIONS

Schedule 40 PVC (Pipe)

D1785

Schedule 40 PVC (Cellular Core Pipe)

F891

Schedule 40 PVC (Fittings)

D2466

Schedule 40 CPVC (Pipe)

F441

Schedule 40 CPVC (Fittings)

F438

SDR-21 PVC or SDR-26 PVC (Pipe)

D2241

SDR-21 CPVC or SDR-26 CPVC (Pipe)

F442

Schedule 40 ABS Cellular Core DWV

(Pipe)

F628

Schedule 40 ABS (Pipe)

D1527

Schedule 40 ABS (Fittings)

D2468

ABS-DWV (Drain Waste & Vent) (Pipe &

Fittings)

D2661

PVC-DWV (Drain Waste & Vent) Pipe &

Fittings)

D2665

PRIMER & SOLVENT CEMENT

ASTM

SPECIFICATION

PVC & CPVC Primer

F656

PVC Solvent Cement

D2564

CPVC Solvent Cement

F493

ABS Solvent Cement

D2235

PVC/CPVC/ABS All Purpose Cement

For Fittings & Pipe of the same material

D2564, D2235,

F493

ABS to PVC or CPVC Transition Solvent
Cement

D3188

CANADA PIPE & FITTING & SOLVENT
CEMENT

MARKING

PVC & CPVC Pipe and Fittings

ULCS636

PVC & CPVC Solvent Cement
ABS to PVC or CPVC Transition

Cement

POLYPROPYLENE VENTING SYSTEM

PolyPro® by Duravent
InnoFlue® by Centrotherm

UL 1738 CERTIFIED GAS VENTING SYSTEM

IPEX System1738 Schedule 40 PVC

Pipes and Fittings

UL1738

IPEX System1738 PVC FGV Cement &

Primer

CAUTION

Solvent cements for plastic pipe are flammable liquids

and should be kept away from all sources of ignition.

Do not use excessive amounts of solvent cement when

making joints. Good ventilation should be maintained to

reduce fire hazard and to minimize breathing of solvent

vapors. Avoid contact of cement with skin and eyes.

DANGER

DANGER OF EXPLOSION!

Fumes from PVC glue may ignite during system check.

Allow fumes to dissipate for at least 5 minutes before

placing unit into operation.

IMPORTANT

SLP99UHV exhaust and intake connections are made

of PVC. Use PVC primer and solvent cement when

using PVC vent pipe. When using ABS vent pipe, use

transitional solvent cement to make connections to the

PVC fittings in the unit.

Use PVC primer and solvent cement or ABS solvent ce-

ment meeting ASTM specifications, refer to TABLE 21.

As an alternate, use all purpose cement, to bond ABS,

PVC, or CPVC pipe when using fittings and pipe made of

the same materials. Use transition solvent cement when

bonding ABS to either PVC or CPVC.
Low temperature solvent cement is recommended. Metal

or plastic strapping may be used for vent pipe hangers.

Uniformly apply a liberal coat of PVC primer for PVC

Содержание SIGNATURE SLP99UH070XV36B





















































































Результаты поиска

Содержание SIGNATURE SLP99UH070XV36B

Отзывы:

Похожие инструкции для SIGNATURE SLP99UH070XV36B

Бренды по названию

Популярные бренды

Lennox SIGNATURE SLP99UH070XV36B, Информация об устройстве

Результаты поиска

Содержание SIGNATURE SLP99UH070XV36B

Отзывы:

Похожие инструкции для SIGNATURE SLP99UH070XV36B

Бренды по названию

Популярные бренды