Lennox SIGNATURE SLP99UH070XV36B Скачать руководство пользователя

Страница: 36 / 84

Page 36

Motor Start-Up

When B3 begins start-up, the motor gently vibrates back

and forth for a moment. This is normal. During this time

the electronic controller is determining the exact position

of the rotor. Once the motor begins turning, the controller

slowly eases the motor up to speed (this is called “soft-

start”). The motor may take as long as 10-15 seconds

to reach full speed. If the motor does not reach 200 rpm

within 13 seconds, the motor shuts down. Then the motor

will immediately attempt a restart. The shutdown feature

provides protection in case of a frozen bearing or blocked

blower wheel. The motor may attempt to start eight times.

If the motor does not start after the eighth try, the control-

ler locks out. Reset controller by momentarily turning off

power to unit.

The DC filter capacitors inside the controller are connect

ed electrically to the motor supply wires. The capacitors

take approximately 5 minutes to discharge when the dis-

connect is opened. For this reason it is necessary to wait

at least 5 minutes after turning off power to the unit before

attempting to service motor.

DANGER

Disconnect power from unit and wait at least

five minutes to allow capacitors to discharge

before attempting to service motor. Failure to

wait may cause personal injury or death.

Power Choke (L13)

A choke coil is used on 4 and 5 ton units equipped with

1 hp motors. The choke is located on the blower housing

and is used to suppress transient current spikes.

Troubleshooting Motor Operation

To verify motor operation see steps below.

1 - Remove J48 (5 pin power plug) from P48 on the

motor.

2 - With the power on at the furnace and door switch

depressed, use a test meter to verify 120V between

pins 4 and 5 on J48.

3 - Reconnect J48 to P48 on the motor.
4 - Remove J49 (4 pin low voltage connector) from P49

on the motor.

5 - Using test jumpers, apply 24V to pins 3 and 4 on

P49 on the motor.

Note:

Do not apply 24V to pins 2 and 4 on P49.

Doing so will cause permanent damage to the motor.

6 - Motor should run at 75%.
7 - Test is complete. Remove jumpers and reconnect

plugs.

Another option is to use the TECMate PRO motor tester

with the 16 to 4 pin adaptor. The use of the TECMate PRO

isolates the motor from the integrated control. Follow the

instructions provided with the kit. If the motor runs do not

replace.

BLOWER B3 HARNESS CONNECTORS

MOTOR with INTEGRATED

CONTROLLER

SHAFT

P49 4 Pin

P48 5 Pin

J48 5 Pin Line Voltage Connector

J49 4 Pin Control Connector

J48 5 Pin

J49 4 Pin

FIGURE 9

Содержание SIGNATURE SLP99UH070XV36B





















































































Результаты поиска

Содержание SIGNATURE SLP99UH070XV36B

Отзывы:

Похожие инструкции для SIGNATURE SLP99UH070XV36B

Бренды по названию

Популярные бренды

Lennox SIGNATURE SLP99UH070XV36B, Информация об устройстве

Результаты поиска

Содержание SIGNATURE SLP99UH070XV36B

Отзывы:

Похожие инструкции для SIGNATURE SLP99UH070XV36B

Бренды по названию

Популярные бренды