Lennox SIGNATURE SLP99UH070XV36B Скачать руководство пользователя | Manualshive

Страница: 73 / 84

background image

Page 73

39 - Reinstall gas valve manifold assembly. Reconnect

gas supply line to gas valve.

40 -  Reinstall burner box cover.
41 -  Reconnect 2-pin plug to gas valve.
42 -  Replace the blower compartment access panel.
43 -  Refer to instruction on verifying gas and electrical

connections when re-establishing supplies.

44 - Follow lighting instructions to light and operate

furnace for 5 minutes to ensure that heat exchanger

is clean and dry and that furnace is operating

properly.

45 - Replace heating compartment access panel

Cleaning the Burner Assembly

1 -

Turn off electrical and gas power supplies to furnace.

Remove upper and lower furnace access panels.

2 -   Disconnect the 2-pin plug from the gas valve.
3 -   Remove the burner box cover.
4 -   Disconnect the gas supply line from the gas valve.

Remove gas valve/manifold assembly.

5 - Mark and disconnect sensor wire from the sensor.

Disconnect 2-pin plug from the ignitor at the burner

box.

6 - Remove four screws which secure burner box

assembly to vest panel. Remove burner box from the

unit.

7 - Use the soft brush attachment on a vacuum cleaner

to gently clean the face of the burners. Visually

inspect the inside of the burners and crossovers for

any blockage caused by foreign matter. Remove

any blockage.

8 - Reconnect the sensor wire and reconnect the 2-pin

plug to the ignitor wiring harness.

9 - Reinstall the burner box assembly using the existing

four screws. Make sure that the burners line up in

the center of the burner ports.

10 -

Reinstall the gas valve manifold assembly.

Reconnect the gas supply line to the gas valve.

Reinstall the burner box cover.

11 -  Reconnect 2-pin plug to gas valve.
12 -  Replace the blower compartment access panel.
13 -  Refer to instruction on verifying gas and electrical

connections when re-establishing supplies.

14 - Follow lighting instructions to light and operate

furnacefor 5 minutes to ensure that heat exchanger

is cleanand dry and that furnace is operating

properly.

15 - Replace heating compartment access panel.

Burner Box Assembly

burner assembly

rollout switch

ignitor

flame sensor

burner box front cover

(remove screw to open cover)

sight glass

intake air collar

Cover plate

(-090XV60C model only)

FIGURE 61

«
...
71
72
73
74
75
...
»

Содержание SIGNATURE SLP99UH070XV36B





















































































Отзывы:

Нет отзывов

Похожие инструкции для SIGNATURE SLP99UH070XV36B

S9V2B040D3PSBC/D

Бренд: Ingersoll-Rand Страницы: 108

Бренд: Williams Страницы: 20

Бренд: American Standard Страницы: 24

Бренд: Daikin Страницы: 74

Бренд: York Страницы: 44

Бренд: Nordyne Страницы: 36

Comfort Pack CP9 T Series

Бренд: NCP Страницы: 44

Бренд: Carrier Страницы: 12

Бренд: Fire Chief Страницы: 27

Бренд: Lennox Страницы: 54

Бренд: Lennox Страницы: 62

Бренд: Nordyne Страницы: 28

Бренд: Whip Mix Страницы: 24

SIGNATURE SLP99DF070V36

Бренд: Lennox Страницы: 71

33” Multi-position Gas Furnaces

Бренд: Johnson Controls Страницы: 6

Бренд: Johnson Controls Страницы: 8

Бренд: Johnson Controls Страницы: 30

Бренд: Rinnai Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды