manualshive.com logo in svg

Lennox SIGNATURE SLP99UH070XV36B, Информация об устройстве

Поделиться
Скачать
Lennox SIGNATURE SLP99UH070XV36B Скачать руководство пользователя страница 44

Page 44

II-Communicating Thermostat (if applicable)

In communicating applications a communicating thermostatmust be used. In these applications the thermostat overrides 

the DIP switch settings on the integrated control. Refer to the illustrations provided with the thermostat for installation, set-

up and operation. See FIGURE 19 and FIGURE 20 for thermostat wiring in communicating applications.

Communicating Enabled Furnace and

Non-Communicating Outdoor Unit

COMMUNICATING

ENABLED FURNACE

COMMUNICATING

THERMOSTAT

NON-COMMUNICATING

OUTDOOR AIR

CONDITIONING UNIT -

1 OR 2 STAGE

OPTIONAL

OUTDOOR

AIR SENSOR

OPTIONAL

DISCHARGE

AIR SENSOR

Communicating Enabled Furnace and

Communicating Enabled Outdoor Unit

COMMUNICATING ENABLED

OUTDOOR UNIT

OPTIONAL

OUTDOOR

AIR SENSOR

OPTIONAL

DISCHARGE

AIR SENSOR

CLIP Y1 TO Y2 FOR

TWO-STAGE OPERATION

Indoor Unit

Controller

Outdoor Unit

Communicating  Thermostat

Single wire to

terminal C

Single wire to

terminal C

Unused wires

Unused wires

Communicating  systems  using  the  a  communicating  thermostat  require  four

thermostat wires between the thermostat and the furnace/air handler control and

four wires between the outdoor unit and the furnace/air handler control. When

a thermostat cable with more than four wires is used, the extra wires must be

nected.

Use wire nuts to bundle the four unused wires at each end of the cable. A

single wire should then be connected to the indoor unit end of the wire bundle

and attached to the “C” terminals as shown in the diagram above.

COMMUNICATING

ENABLED FURNACE

COMMUNICATING

THERMOSTAT

FIGURE 19 

Содержание SIGNATURE SLP99UH070XV36B





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды