Allied 96G2DFV Скачать руководство пользователя страница 1

Страница: 1 / 53

507962-01

Page 1 of 53

Issue 2149

INSTALLATION INSTRUCTIONS

96G2DFV

Warm Air Gas Furnace / Downflow Air Discharge

Direct Vent & Non-Direct Vent

Save these instructions for future reference

(P) 507962-01

*P507962-01*

Manufactured By

Allied Air Enterprises LLC

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in manuals, be alert to

the potential for personal injury or death.

Improper installation, adjustment, alteration, service

or maintenance can cause property damage, personal

injury or loss of life. Installation and service must be

performed by a licensed professional installer (or

equivalent), service agency or the gas supplier.

WARNING

As with any mechanical equipment, personal injury can

result from contact with sharp sheet metal edges. Be

careful when you handle this equipment.

CAUTION

Table of Contents

Unit Dimensions

..........................................................

Parts Arrangement

.......................................................

Gas Furnace

................................................................

Shipping and Packing List ...........................................

Safety Information

.......................................................

General

........................................................................

Combustion, Dilution & Ventilation Air

.........................

Installation

.................................................................

Filters

.........................................................................

Duct System

..............................................................

Venting Practices

.......................................................

Condensate Piping

....................................................

Gas Piping

.................................................................

Electrical

....................................................................

Testing for Proper Venting and Sufficient Combustion

Air for Non-Direct Vent Applications

..........................

Unit Start-Up

..............................................................

Blower Performance

..................................................

Service

.......................................................................

Planned Service

........................................................

Repair Parts List

........................................................

Содержание 96G2DFV






















































Результаты поиска

Содержание 96G2DFV

Отзывы:

Похожие инструкции для 96G2DFV

Бренды по названию

Популярные бренды

Allied 96G2DFV, Руководство по установке

Результаты поиска

Содержание 96G2DFV

Отзывы:

Похожие инструкции для 96G2DFV

Бренды по названию

Популярные бренды