Lennox ComfortSense 7500 Скачать руководство пользователя | Manualshive

Страница: 41 / 56

background image

41

AUXILIARY DEHUMIDIFIER

The auxiliary dehumidifier setting is used when a
whole home dehumidifier is used for
dehumidification. This requires:

1. Whole home dehumidifier has been wired to

thermostat per dehumidifier installation
instructions.

2. Dehumidification has been enabled on

installer settings

.

3. Unit is in COOL mode, (or if in AUTO, there

has

been at least one thermostat cooling call

made prior to

the dehumidification demand)

.

4. Dehumidification demand exists (RH above

set point).

HUMIDITROL

®

If Humiditrol is enabled in the installer settings,
then this adjustment affects overcooling
operation. Overcooling ranges from 2ºF below the
cooling setpoint (

MIN

setting) down to 2ºF above

the heating setpoint (

MAX

setting). Halfway

between the two settings is the

MID

setting.

If a Humiditrol

®

EDA is installed and enabled, then

the thermostat must be configured to properly
operate the Humiditrol

®

EDA as follows (see

Figure 22 for the Humiditrol

®

EDA operation

flowchart):
Check the HUMIDITY SETTINGS in user settings
to confirm that the user has turned

ON

dehumidification setting.

NOTE - Humiditrol

®

EDA operation requires use

of an outdoor sensor. If sensor is not connected
and Humiditrol

®

EDA is enabled, “OUTDOOR

SENSOR REQUIRED” is displayed in the
information display.

Cooling only

—

Dehumidification will only occur if:

1. Dehumidification demand is present.
2. Cooling demand is not present.
3. Outdoor temperature is less than 95ºF,
4. Indoor temperature is not cooler than 65ºF or

cooler than the heating set point + 2ºF (

IF

the

difference between cooling and heating set
points is greater than the deadband).

In this case, 24VAC is removed from the

D

terminal and

Y1

and

Y2

terminal (if available)

becomes activated with 24VAC. This cycles the

«
...
39
40
41
42
43
...
»

Содержание ComfortSense 7500

























































Отзывы:

Нет отзывов

Похожие инструкции для ComfortSense 7500

Бренд: Karandash Страницы: 6

Бренд: Taylor Страницы: 6

Бренд: RELSIB Страницы: 2

SF-HANHELD-160T05

Бренд: Safire Страницы: 12

Vision Wireless BT-A03 RF

Бренд: Watts Страницы: 2

Бренд: cor thermostat Страницы: 40

Бренд: E+E Elektronik Страницы: 17

Бренд: Vava Страницы: 5

Tempatch ECH-b1-L

Бренд: ECH Medical Instrument Страницы: 9

Бренд: Xylem Страницы: 30

Бренд: Jaga Страницы: 16

Бренд: Edison Страницы: 8

Бренд: Brooks Страницы: 2

Remote Thermometer

Бренд: Maverick Страницы: 2

Бренд: North Страницы: 21

Бренд: TOTALINE Страницы: 26

Бренд: TOTALINE Страницы: 28

Бренд: TOTALINE Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды