Lennox ComfortSense 7500 Скачать руководство пользователя | Manualshive

Страница: 42 / 56

background image

42

indoor variable speed motor to the
dehumidification speed and cycle Y2

ON

to the

outdoor unit. Cooling has priority over Humiditrol

®

calls. Humiditrol

®

mode is allowed to over cool up

to 2

º

F above the heating set point.

Heat only

—

Thermostat will cycle heating ON and

OFF to maintain heating set point.
Dehumidification functions are disabled.

Heat/Cool

—

Dehumidification will only occur if a

dehumidification demand is present, a cooling
demand is not present, outdoor temperature is
less than 95ºF, indoor temperature is above 65ºF
and the indoor temperature is not cooler than 2ºF
above heating set point.

Note: If the last thermostat demand was a heating
demand, the thermostat does not require a cooling
demand before Humiditrol

®

operation.

Humidity Sensor Fault

If the humidification sensor fault occurs, then the

H

terminal becomes inactive, and the

D

terminal

goes to 24VAC.

Dew point adjust is only available when an outdoor
sensor is attached.

Other Humiditrol

®

EDA Notes

If the outdoor sensor is disconnected while
HUMIDITROL is enabled, the thermostat will not
allow operation in dehumidification mode.
Set point range: 45 to 60% Relative Humidity
(RH). Factory default - 50%.
Relative Humidity controls to within 2% on either
side of RH set point.
When the “D” terminal is activated with 24VAC,
dehumidification is inactive.
NORMAL, MAX and HUMIDITROL

modes are

disabled by default from the factory.
As a precaution, regardless of how low the heating
set point has been set, Humiditrol

®

dehumidification is inhibited below 65

º

F indoor

temperature.

Unit Part (Catalog) & Serial Numbers

A label on the back of the thermostat is visible
through an opening in the back of base plate. This
identifies the Lennox Catalog Number, Part

«
...
40
41
42
43
44
...
»

Содержание ComfortSense 7500

























































Отзывы:

Нет отзывов

Похожие инструкции для ComfortSense 7500

Бренд: Saswell Страницы: 5

TTY6800Z Series

Бренд: Azbil Страницы: 20

Бренд: Coronado Страницы: 3

Бренд: Lauda Страницы: 52

Бренд: Axio Страницы: 4

thermoadvanced easy

Бренд: miniland Страницы: 140

Бренд: Kampmann Страницы: 20

Бренд: Citizen Страницы: 52

Бренд: TCS Basys Controls Страницы: 18

Бренд: Tekmar Страницы: 2

ComfortNET CTK04

Бренд: Honeywell Страницы: 24

CONVERTASTAT TP970A2145

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 4

Бренд: Silvercrest Страницы: 125

tekmarNet 4 544

Бренд: Tekmar Страницы: 12

Бренд: Tekmar Страницы: 24

Бренд: Honeywell Страницы: 4

ultrastat CT1700A

Бренд: Honeywell Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды