manualshive.com logo in svg

Lennox ComfortSense 7500, Инструкция по установке и настройке

Поделиться
Скачать
Lennox ComfortSense 7500 Скачать руководство пользователя страница 39

39

Rh 

set point

=

Outdoor Temp (ºF)

2

+ 25

+

RH

user dew point
adjustment

Where:

RH

user dew point adjustment 

cannot /-15% and

Rh

setpoint

 minimum is 15% and cannot exceed 45%.

DEW POINT NORMAL & MAX

Dew point adjustment mode will change the
humidification set point based on the outdoor
temperature and a user-defined dew point
adjustment setting.

NOTE - In dew point adjustment mode, the
humidification set point has no effect whatsoever
on unit operation. Only the user-defined dew point
adjustment setting affects operation per the
following the above formula.

Dehumidify

Dehumidification

 

(removing moisture from air) can

occur only when the thermostat is in 

cool mode

.

When a dehumidification demand is present, a
dehumidification signal (0VAC - open circuit) is
present at the D terminal. This is used to reduce

the speed of the indoor blower during
dehumidification. At the same time, the Y1 and Y2
(if available) terminals become activated with
24VAC. The H terminal is inactive (0VAC - open
circuit) during dehumidification.
System must be in cool mode and had one call for
AC before feature is active. Once dehumidification
is active the dehumidification modes are as
follows:

Normal: 

Runs dehumidification with a call for

cooling and dehumidification.

Max: 

Runs dehumidification with a

dehumidification call but without a call for
cooling.

Auxiliary Dehumidifier: 

Runs based on

humidity reading from thermostat's internal
humidity sensor and will call for
dehumidification using the auxiliary
dehumidifier (whole house dehumidifier).

Содержание ComfortSense 7500

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды