24
L-65 PARTS DIAGRAM & PARTS LIST
May00
Pos. Part nos.
Description
Qty.
L032-030 L-65 airless gun without tip nut
L032-035 L-65 airless gun without tip nut (G-thread)
1
L032-501 Tip retainer (11/16" L-thread)
opt.
L032-710 Tip retainer (7/8" G-thread)
opt.
2
tip (see separate list)
opt.
3
L043-008 Nylon washer
1
4
L032-711 Seat, (11/16" L-thread)
1
L032-712 Seat, (7/8" G-thread)
1
5
L032-589 Trigger guard
1
6
L032-523 Trigger pin
1
7
L032-713 Trigger complete
1
8
L032-714 Gun body
1
9
L032-591 Pin
2
10
L032-715 Ball with shaft
1
11
L032-507 Wedge
1
12
L032-508 Packing
1
13
L032-716 Housing
1
14
L032-582 Spring shaft
1
15
L032-588 Spring
1
16
L032-583 Housing nut
1
17
L032-587 Retainer cap
1
18
L032-590 Lock nut
1
19
L032-514 Handle seal
1
20
L032-516 Gun filter, white (50 mesh)
1
L032-517 Gun filter, yellow (100 mesh)
opt.
L032-518 Gun filter, red (200 mesh)
opt.
21
L032-519 Filter spring
1
22
L032-717 Handle
1
23
L032-520 Copper seal
1
24
L032-521 Swivel, 1/4" nps
1
Accessories:
L032-718 Repair kit, L-65-L (#4,10,12,14,18)
L032-719 Repair kit, L-65-G (#4,10,12,14,18)
Pos. Part nos. Description Qty.
Turning this
nut tightens the
packing. Check
occationally and do
not over tighten.
HIGH PRESSURE!
INJECTION HAZARD!
Specifications, L-65
Maximum pressure: 3600 psi.
Tip thread: 11/16-16 or 7/8-14.
Hose connection: 1/4" nps.
Wetted parts: Al,SS,TC,Cu,
Brass,Tef.
Important
To engage trigger
safety lock, turn
lever tab to horizon-
tal position. Test
regularily for proper
functioning while
system is shut
down.
(trigger shown in horizontal
locked position)
locked
unlocked
• Remove filter for cleaning, then reinstall and hand tighten the handle.
• To clean gun: flush the inside by spraying proper solvent, and wipe the
exterior. (It is not neccessary to disassemble gun components under normal
circumstances).
• Follow shut down procedure before
servicing or cleaning equipment. (see #1
overleaf)
• This instruction sheet is only a supplement to
your system operating instructions. Read your
system manual before operating any high
pressure equipment.
Procedure, then follow the spray tip manufacturer’s instructions for removing and cleaning the
spray tip.
• Never attempt to change spray tip or leave the unit unattended without first shutting off
pump, releasing fluid pressure, and locking the trigger safety lock.
• Conductive metal containers must be used when flushing flammable fluids through
the system. Always flush at low pressure with spray tip removed. A metal part of the spray
gun must be held firmly against the grounded metal pail when flushing or relieving pressure
from the gun.
• Trigger guard helps reduce the risk of accidentally triggering the gun if dropped or bumped.
Do not use a spray gun without a trigger guard.
16
17
18
15
14*
13
12
19
11
24
23
22
21
6
7
8
5
4
3
2
9
1
10*
20
9
Important: this "double lip" end
of filter must go in the gun first.
o
• Injection hazard: Airless Painting Equipment can cause serious injury if the spray
penetrates the skin. Do not point the gun at anyone or any part of the body. The tip guard
provides some protection against accidental injection injuries, but is mostly a warning
device. Never put your hand, fingers or body over the spray tip. Gloves and clothing do not
necessarily offer any protection either. Keep the gun trigger safety lever in locked postion
when not spraying. Always have the tip guard in place while spraying.
In case of penetration seek medical aid immediately!
Note to physician: Injection
into skin is a serious traumatic injury. It is important to treat the injury surgically as
soon as possible. Do not delay treatment to research toxicity. Toxicity is a concern
with some exotic coatings injected into the bloodstream. Consultation with a plastic
surgeon or reconstructive hand surgeon may be advisable. Be prepared to tell the
doctor what fluid was injected.
• Do not use halogenated hydrocarbon solvents in this system; it contains aluminium
parts and may explode. Cleaning agents, coatings, paints, and adhesives may contain
halogenated hydrocarbon solvents. Don't take chances, consult your material supplier to be
sure. (ex: methylene chloride and 1,1,1 - Trichlorethane)
• Caution: When a flammable liquid is sprayed there may be danger of fire or explosion
especially in a closed area.
• Use extreme caution when cleaning spray tip guard. DO NOT try to wipe off build up
around the spray tip before following shut down procedure. Follow the Shut down
* note: once #10
& #14 are
assembled, the
length from end
to end must be
88 - 88.5 mm.
