Lehner Lifttechnik OMEGA - F Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 47

background image

OMEGA

Installation Manual

Edition July 2013

Omega

platform lift

page 43 of 46

Configuration of the remote radio controls

2 different systems are offered for the Omega system. The used system has to be defined
in the menu and there 2 different ways to programme the remote radio senders.

Version Schmidiger:

To programme the remotes the button S2 on the control board where the receiver is
connected to has to be pressed until the LED on the receiver start to blink.
Now the senders can be programmed. To programme a sender the up and down button on
the sender have to be pressed simultaneously. Then the LED on the sender start to blink in
orange for 2,5 second and then remains on in an orange light. Now the sender is
programmed. Then the next sender can be programmed in the same way.
To stop the programming mode the button S2 has to be pressed again and the action will
be confirmed by the receiver by fast blinking of the LED.

The remote radio controls have a LED status indications. The below status refers to the
radio control model Schmidiger TX-OMDE-V-01:

LED status

Description

Green light

Radio signal ok and drive command is active

Orange light

Radio signal ok and platform is not driving or folding

A reason can be that the platform is driven from the platform control
or that a safety circuit is open in the electrical system.

Red light

Radio signal is ok but the lift is not moved by the command.

Orange blinking

Radio signal is not ok

– there is a disruption

Red blinking

The batteries of the sender a weak and should be changed

Green blinking

The sender was successfully connected to the receiver during
programming

Version TeleRadio:

To programme the remotes the button S2 on the control board where the receiver is
connected to has to be pressed for 1-6 seconds. After releasing the button S2 the receiver
waits for 5 seconds that any button on the sender to programme is pressed for at least 2
seconds. After he receives the signal from the sender the receiver goes back into normal
operation mode and the sender is saved. Then the next sender can be programmed in the
same way.
The controls show a green light when switched on and shows a blinking light a command
button is pressed. If there is not light then the control is not working.

«
...
42
43
44
45
46
...
»

Содержание OMEGA - F
















































Отзывы:

Нет отзывов

Похожие инструкции для OMEGA - F

Бренд: Bruno Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды