manualshive.com logo in svg

Lehner Lifttechnik OMEGA - F, Руководство по установке

"Lehner Lifttechnik OMEGA - F" - надежный и эффективный подъемный механизм, предназначенный для установки грузов на различных высотах. Установочное руководство можно загрузить бесплатно с нашего сайта. manualshive.com. Обеспечьте безопасность и профессиональный монтаж с помощью этого руководства.

Поделиться
Скачать
background image

 

OMEGA

 Installation Manual 

Edition July 2013 

 

Omega

 platform lift 

page 28 of 46 

If an intermediate landing station is saved then after the confirmation with the alarm button 
a M will be shown beside the point number 

– see illustration below: 

 

 
 
 
 
 

 

If the platform is in the upper landing station and the last point was saved by pressing the 
alarm button it is necessary to stop the teach-in process. This has to be done in the main 
menu with the menu item: “teach-in stop”. If this item is confirmed with the downward 
directional button the programming on the points is complete and the unit can be run down 
to test the changing of the speeds in the saved points. 
 
If there is a problem with the teach-in process and a point cannot be saved then one of the 
following error messages will show on the display:   
 

Display 

Description 

invalid interval 

The platform always has to drive with curve speed (slow 
speed) into a landing station. Otherwise this error will show. 

point too close 

The distance between 2 points is too close. It is important 
to keep a minimum distance of 150mm between 2 points.   

invalid teach in 

At the end of the teach-in drive the relations of the saved 
points are checked. If they are invalid this error will show.   

rail too long 

If this error is shown the total length of the rail is too long. 
Please contact the supplier. 

too many points 

A maximum of 40 points can be saved. This number cannot 
be exceeded.   

 
In case of such an error the teach-in process cannot be continued. It is necessary to drive 
down to the lower landing station and start the whole process again by activating the teach-
in start item in the main menu!  
 
If on the display a failure code can be seen please check in the error code list for what the 
problem can be. This failure codes are not related to the teach-in process. 
 
  

 

 
 
 

 

The point in the 

intermediate landing 

station was saved 

Error code 10 shown 

on display 

Содержание OMEGA - F
















































Отзывы:

Нет отзывов

Похожие инструкции для OMEGA - F

Бренды по названию

Популярные бренды

Загрузить еще бренды