Lehner Lifttechnik OMEGA - F Скачать руководство пользователя страница 32

Страница: 32 / 47

OMEGA

Installation Manual

Edition July 2013

Omega

platform lift

page 31 of 46

Name

Number

Reaction

Possible reason

Short circuit
between the
support rope and
the rail

15 (F)

Drive only till the
next landing
station, then stop

If there is a short circuit between the
support rope and the rail

SPI Timeout on
drive unit

16 (1.)

Drive is stopped

The communication between the PIC
microcontroller and the Echelon
Powerline module was defunct or not
correctly adjusted.

Safety circuit

17 (2.)

Drive is stopped

Safety circuit relays (KAUF, KAB) on
the platform are not released.

FI-communication 18 (3.)

Only slow drive
possible

The communication with the
frequency inverter via the RS485
Modbus interface did not work.

Communication
with EEPROM on
drive unit

19 (4.)

The communication between the
micro controller and the EEPROM on
the drive unit did not work.

Feedback from
main contactors

20 (5.)

Drive only till the
next landing
station, then stop

One of the main drive contactors or
the safety circuit relay KSK has not
been released after the platform
stopped driving.

Data transfer
between the drive
unit and the
platform control

21 (6.)

Drive is stopped

The communication via the tension
rope did not work correctly. This
failure is detected on the drive unit.

SPI Timeout
Platform

112 (-)

Drive is stopped

The communication between the PIC
micro controller and the Echelon
Powerline module was not correct.
The Powerline module is defect or
not correctly plugged.

Data transfer
between the drive
unit and the
platform control

113 (-)

Drive is stopped

The communication via the tension
rope did not work.

Communication
with EEPROM on
platform

115 (-)

Drive is stopped

The communication of the micro
controller with the EEPROM on the
platform control did not work.

Содержание OMEGA - F
















































Результаты поиска

Содержание OMEGA - F

Отзывы:

Похожие инструкции для OMEGA - F

Бренды по названию

Популярные бренды

Lehner Lifttechnik OMEGA - F, Руководство по установке

Результаты поиска

Содержание OMEGA - F

Отзывы:

Похожие инструкции для OMEGA - F

Бренды по названию

Популярные бренды