1PH Platinum Luxury-Lift
®
with
Adjustable Headrest & Lumbar Operating Instructions
1PH Platinum Luxury-Lift
®
with
Adjustable Headrest & Lumbar Operating Instructions
21
20
– To reduce the risk of serious injury or death:
• Do not let children play on or near the chair when in use. Serious injury or death could
occur if head or body parts are under the chair when the chair is in motion.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle
the plug or remote control with wet hands.
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
DANGER
Getting Started
Connect the power supply connector to the connector at the base of the lift chair. Connect
the 120 volt power cord to the power supply. Plug the power supply
directly
into a wall outlet.
Platinum Luxury-Lift
®
with Adjustable Headrest and Lumbar Operation
The
1PH
offers multiple modes of operation. The large, round
LIFT
and
RECLINE
button on the front
of the hand wand AND the toggle on the back of the hand wand provide coordinated movements.
The
LIFT
and
RECLINE
button and back toggle will operate all functions of the chair in one fluid
movement from sitting, reclining and legrest extension, back to the upright position and standing.
Individual movement of the back and legrest can be achieved by pressing the
BACK
button to recline
and return the back of the unit, and by pressing the
LEGREST
button to extend and return the legrest.
Customized comfort is achieved by pressing the
HEADREST
button to set the angle of the headrest tilt
and the
LUMBAR
button to set the intensity of the lumbar.
– To reduce the risk of serious injury:
• The 1PL, 1PM and 1PH lift chairs are intended for a single occupant, not exceeding 350
pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close
the legrest.
• Unit is designed to ease exit from the chair. Take care to not slip out of chair when
chair is in motion.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
– To reduce the risk of product damage:
• After 2 minutes of continuous operation of the 4LP, 1PL, 1PM, 1PH and 1HM chairs,
allow the lift and recline features to rest for 18 minutes.
NOTICE
To recline the chair:
As with the lift feature, there are multiple modes of operation to recline the chair. The back and
legrest recline movements are both synchronous and independent. The back and legrest recline
are programmed to move together using the front, large round
LIFT
and
RECLINE
button at the
top of the hand wand, or the toggle on the back of the hand wand. The back and legrest recline
are programmed to move independently using the front, oblong
BACK
and
LEGREST
buttons. The
independent operation allows you to recline the back without raising the legrest, raise the legrest
without reclining the back, or make individual adjustments to the back and legrest recline, which
are outside the synchronous movement.
1.
With the chair in the seated position, to recline the back and raise the legrest at the same
time, press and hold the front, large round
RECLINE
button, or press the back
toggle up
and
hold. To recline only the back or raise only the legrest, press and hold down on the right side
of the appropriate front, oblong
BACK
or
LEGREST
button. Release the button or toggle when
you are in a comfortable position.
2.
Make adjustments to the back and legrest recline as preferred.
3.
To return the chair to the upright, seated (home) position, press and hold down on the front,
large round
LIFT
button, or press and hold the back
toggle down
. Release the button or toggle
when you reach the upright, seated (home) position. There is a two second delay that occurs
when the chair arrives at its seated, home position; the chair starts the lift function after the
delay when the front, large round button or back toggle is pressed and held. Additionally, you
may press and hold down on left side of the front, oblong
BACK
button, followed by the
LEGREST
button, releasing the button when the movement reaches its end of travel and stops.
To stand up from the chair:
There are multiple modes of operation for the lift feature. Both the front, large round
LIFT
button
at the top and the back toggle provide a coordinated movement of the lift function. The back must
be fully upright and the legrest fully closed for the lift feature to function.
1.
Firmly position your feet on the floor to maintain balance and prevent sliding or falling. Press
down on the front
LIFT
button and hold, or press the back
toggle down
and hold, to raise the
chair to the standing position.
2.
Release the button or toggle when the chair reaches a height that enables you to comfortably
stand. Carefully exit the chair.
3.
Return the chair to the seated (home) position if you will be away from the chair for an
extended period of time. Press down on the front
RECLINE
button and hold, or press the back
toggle up
and hold to lower the chair. Release the button or toggle when the chair is in its
seated (home) position.
NOTE: The system includes a built-in two second delay that occurs when the chair arrives at its
seated, home position. The chair starts the reclining function immediately following the two second delay.
To sit down in the chair:
1.
Stand beside the chair and press down on the front
LIFT
button and hold, or press the back
toggle down
and hold. Release the button or toggle when the chair reaches a comfortable height
to sit against, depending on your personal needs and preference.
2.
Step back into the chair and sit in the center of the seat while keeping your feet firmly
on the floor.
3.
Press down on the front
RECLINE
button and hold, or press the back
toggle up
and hold to lower
the chair. Release the button or toggle when the chair reaches the seated, home position. There
is a two second delay that occurs when the chair arrives at its seated, home position; the chair
starts the recline function after the delay.
