LawnMaster NPTGSP2517A Скачать руководство пользователя страница 40

Страница: 40 / 50

NOPULL

STARTER SYSTEM

Special troubleshooting instructions for No-Pull™ Start Button

(See Figs.

80-87)

Starting Operation

Lift the start button cover and press the start button to start the electric motor. Release the start button
to stop the electric motor (Fig. 80).

NOTE:

When the start button remains pressed, the electric motor will run for about 5 seconds then

it will stop automatically. When this occurs, release the start button and press it again to re-start the
electric motor.

Troubleshooting

■ The electric motor does not start when pressing the start button. According to LED indictors, the

possible causes as below:

A. Yellow flashing of the battery indicator LED indicates battery cells are too hot and needs to cool to

room temperature (Fig. 81).

During starting process the LED will indicate the battery voltage as below if there is no alarm indicator:

Tolerance is ±0.2V

Battery Voltage

LED Status

≥7.7V

Green

7.1V-7.7V

Orange

6.6V-7.1V

Red

Fig. 80

LED

Start Button

Stop Switch

Fig. 81

Battery

Cells

NTC

Содержание NPTGSP2517A



















































Результаты поиска

Содержание NPTGSP2517A

Отзывы:

Похожие инструкции для NPTGSP2517A

Бренды по названию

Популярные бренды

LawnMaster NPTGSP2517A, Руководство по обслуживанию

Результаты поиска

Содержание NPTGSP2517A

Отзывы:

Похожие инструкции для NPTGSP2517A

Бренды по названию

Популярные бренды