LawnMaster NPTGSP2517A Скачать руководство пользователя страница 17

Страница: 17 / 50

GENERAL TROUBLESHOOTING

The clutch engages during

idle speed.

Clutch is damaged.

Replace.

The free length of the clutch

spring is too long.

Replace.

Clutch is off center.

Replace.

No load speed is not

stable/consistent.

Incorrect carburetor

adjustment.

Re-adjust the carburetor.

The carburetor has an air

leakage.

Replace or re-tighten.

Fuel tube is broken.

Replace.

Crankcase washer has air

leakage.

Replace.

Fuel seal has air leakage.

Replace.

After releasing the throttle

lever, the trimmer head

continues to rotate.

Idle speed is too high.

Adjust the engine.

Clutch spring is broken.

Replace.

Clutch friction plate is

broken.

Replace.

The engine accelerates,

but the trimmer head does

not rotate.

The axle rotating spline or

the square hole of pawl

assembly is worn out.

Replace.

Irregular vibration.

The trimmer head is not

balanced.

Repair or replace.

The drive shaft is bent.

Replace.

Worn bearings.

Replace.

Clutch is off center.

Replace.

Содержание NPTGSP2517A



















































Результаты поиска

Содержание NPTGSP2517A

Отзывы:

Похожие инструкции для NPTGSP2517A

Бренды по названию

Популярные бренды

LawnMaster NPTGSP2517A, Руководство по обслуживанию

Результаты поиска

Содержание NPTGSP2517A

Отзывы:

Похожие инструкции для NPTGSP2517A

Бренды по названию

Популярные бренды