Lattice Semiconductor ECP5 Versa Скачать руководство пользователя страница 75

Страница: 75 / 86

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-TN-02035-1.3

8.13.

Memory Output DDR Primitives for DQ Output

The following are the primitives used to implement various memory DDR output configurations to generate the DQ
outputs.

8.13.1.

ODDRX2DQA

This primitive is used to generate DQ data output for DDR2 with x2 gearing and for DDR3 memory interface.

SCLK

RST

ODDRX2DQA

ECLK

DQSW270

Figure 8.13. ODDRX2DQA

Table 8.20. ODDRX2DQA Port List

Port

I/O

Description

D0, D1, D2, D3

Data input to the ODDR (D0 is output first, D3 last)

ECLK

Fast Edge Clock input

DQSW270

Clock that is 90° ahead of clock used to generate the DQS output

SCLK

SCLK input

RST

Reset input

DDR data output on both edges of DQSW270

8.14.

Memory Output DDR Primitives for DQS Output

Following are the primitives used to implement the DQS outputs to the DDR memory.

8.14.1.

ODDRX2DQSB

This primitive is used to generate DQS clock output for DDR2 and DDR3 memory.

SCLK

RST

ODDRX2DQSB

ECLK

DQSW

Figure 8.14. ODDRX2DQSB Primitive

Содержание ECP5 Versa























































































Результаты поиска

Содержание ECP5 Versa

Отзывы:

Похожие инструкции для ECP5 Versa

Бренды по названию

Популярные бренды

Lattice Semiconductor ECP5 Versa, Техническая заметка

Результаты поиска

Содержание ECP5 Versa

Отзывы:

Похожие инструкции для ECP5 Versa

Бренды по названию

Популярные бренды